673158
6
Zoom out
Zoom in
Previous page
1/20
Next page
Inst.296 Viron eVo Series Pool & Spa Heater V07_16
6
MAINTENANCE
It is recommended that you check the following at least every six months and at the beginning of every swimming
season.
1. Examine the flue outlet and panel louvers for blockages. Make sure there are no obstructions to the flow
of air to or from the appliance.
2. Keep the heater area clear and free of combustibles and flammable liquids. Chlorine should not be stored in
the vicinity of the heater. Chlorine and acid vapours, when drawn through a heater, can rapidly cause
corrosion of the heat exchanger.
3. Keep the heater area free from garden refuse and debris. This will help prevent insects nesting in the unit
and ensure extended life and reliability of your heater.
4. Have your heater professionally inspected at least every 2 years, preferably every 12 months.
WINTER OPERATION
If the pool won’t be used for a month or more, turn the heater off at the main gas isolation valve. For areas where
there is no danger of freezing, water should circulate through your heater all year long even though you are not
heating your pool.
Where freezing is possible, it is necessary to drain the water from the heater. This may be done by loosening the
inlet or outlet barrel union. If the heater is below water level, isolate it from the pool first by closing shut off valves
before and after the heater.
CAUTION: If the heater has been drained for freezing conditions, do not turn on until the system is circulating
water.
INSTALLATION
THIS APPLIANCE MUST BE INSTALLED BY AN AUTHORISED PERSON. Refer to heater data plate for
specifications of gas type, gas consumption, burner pressure and water pressure.
This appliance must be installed in accordance with local regulations and Australian Standard Installation Code
AS/NZS 5601.
The installer must test the operation of the appliance before leaving.
FLOW RATES
The Viron eVo Pool Heater requires a minimum of 250 litres per minute flow for 250/350 models and 350 litres per
minute flow for 450/550 models. The maximum permissible flow rate is 500 litres per minute. For flow rates in
excess of 500 litres per minute, an external by-pass valve must be fitted.
WATER CONNECTIONS
The heater should always be installed after the pump and filter. The water connections are located on the right
hand side of the heater. The inlet and outlet are clearly marked. Water connections must be completed in 50
mm PVC glue in plumbing.
All automatic sanitising devices must be installed after the heater and in such a way that the sanitiser cannot enter
the heater without first mixing with the water in the pool or spa. Sanitisers that are connected prior to the heater will
void heater warranty.
A non return valve is not required to be fitted between the filter and the heater.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Astralpool Viron eVo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Astralpool Viron eVo in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info