673142
42
Zoom out
Zoom in
Previous page
1/293
Next page
Malfunction
Error code
Reason
Solution
T6 Exhaust too high
protection
EE05
1.Lack of gas
2.Low water flow
3.Pipingsystem has been blocked
4.Exhaust temp. Sensor failure
1. Check the high pressure gauge, if too low, fill
with some gas
2. Check the waterway system and water pump
3. Check the piping system if there was any
block
4. Change a new exhaust temp. sensor
Controller failure
EE06
1. Wire connection is not good, or damaged
signal wire
2. Controller failure
1. Check and re-connect the signal wire
2. Change a new signal wire
3. Turn off electricity supply and restart machine
4. Change anew controller
Compressor current
protection
EE07
1. The compressor current is too large
instantaneously
2. Wrong connection for compressor phase
sequence
3.Compressor accumulations of liquid and oil
lead to the current becomes larger
4. Compressor or driver board damaged
5. The water flow is abnormal
6. Power fluctuations within a short time
1. Check the compressor
2. Check the waterway system
3. Check if the power in the normal
range
4. Check the phase sequence connection
Communication
failure between
controller and main
board
EE08
1. Poor signal wire connection or damaged
signal wire
2. Controller malfunction
1. Check and re-connect the signal wire
2. Change a new signal wire
3. Turn off electricity supply and restart machine
4. Change anew controller
Communication
failure between
Main control board
and Driving board
EE09
1. Poor connection of communication wire
2. The wire is damaged
1. Check the wire connection
2. Change a new wire
VDC voltage too
high protection
EE10
1. Mother line voltage is too high
2. Driver board is damaged.
1. Check if the power is in the normal range
2. Change driver board or main board
IPM module
protection
EE11
1. Data mistake
2. Wrong compressor phase connection
3. Compressor liquid and oil accumulation
lead to the current becomes larger
4. Compressor or driver board damaged
1. Program error, turn off electricity supply and
restart after 3 minutes
2. Change driver board
3. Check compressor sequence connection
VDC voltage too
low protection
EE12
1. Mother line voltage is too low
2. Driver board is damaged.
1. Check if the power is in the normal range
2. Change driver board
8. Troubleshooting
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Astralpool ELYO SMART NN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Astralpool ELYO SMART NN in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 6,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info