673144
25
Zoom out
Zoom in
Previous page
1/196
Next page
ASTRALPOOLHEAT SERIES · AIR/WATER SYSTEM
ASTRALPOOLHEAT SERIES · AIR/WATER SYSTEMASTRALPOOLHEAT SERIES · AIR/WATER SYSTEM
ASTRALPOOLHEAT SERIES · AIR/WATER SYSTEM
© ASTRALPOOL 2015 ALL RIGHTS RESERVED. PROPRIETARY DOCUMENT.
Pag:
25
ENGLISH
ENGLISHENGLISH
ENGLISH
POOL
POOL POOL
POOL &
&&
&
SPA MODE
SPA MODESPA MODE
SPA MODE
When the unit is configured to heat Pool and Spa water, we can use both terminals, EXT #1 and
EXT #2, to gain some extra capabilities (first SPA Control screen on technical menu has to be set
to External control, see 5.7. 17).
5.16.
5.16. 5.16.
5.16. MODBUS
MODBUSMODBUS
MODBUS
This Heat pump includes Modbus capabilities. For complete instructions
for Modbus connection & communication, please consult Modbus manual
at Fluidra PDB (Product Data Base): http://pdb.astralpool.com/pdb/
6.
6. 6.
6. START
STARTSTART
START-
--
-UP PROCEDURE FOR THE UNIT
UP PROCEDURE FOR THE UNITUP PROCEDURE FOR THE UNIT
UP PROCEDURE FOR THE UNIT
Operating requirements for the heat pump:
The outdoor temperature must be higher than +5 ºC.
The heat pump is provided with a defrost thermostat that guarantees compressor
shutdown and the operation of the defrost system.
When washing the filter of the filtering pump, it is MANDATORY to turn off the heat
pump.
Before any start-up, you should check:
The correct clamping of the hydraulic connections (exchanger inlet / outlet).
The correct fastening of the electrical cables to the connection terminals. Poorly
secured terminals can cause the terminal block to heat up.
When setting-up, the electrical connections, as well as the general power supply and
voltage should be verified.
Once the unit is connected, verify the intensity absorbed by the phases and check that
the fan is operating in the correct direction.
Give power to the equipment by connecting the general power switch on the outside of
the unit. Once the unit is connected, verify the intensity absorbed by the phases.
Three-phase units have a phase control relay that guarantees the compressor is
operating in the correct direction. If the controller shows the compressor it is running
and it does not, phases must be interchanged. Card gives an alarm signal.
With the machine running, verify the intensities absorbed by the electric motors,
making sure they do not exceed the limits mentioned in the technical specification
sheet.
Verify that the currents of the different lines are not out of phase except in the case of
single-phase circuits.
High and low pressure switches should be installed in the cooling circuit and verify the
refrigerant charge (Refrigerant Charge section).
Performing the heat pump adjustments in its initial operation
EXT #1
EXT #
2
RESULT:
The unit will work on Pool mode.
The unit will work on Spa mode
The unit will work on Pool + Spa mode
External Stop (same case as in general mode)
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Astralpool ASTRALPOOL HEAT II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Astralpool ASTRALPOOL HEAT II in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 8,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info