628507
32
Zoom out
Zoom in
Previous page
1/112
Next page
EF1210 U
SER
M
ANUAL
30 http://www.aspi.com Copyright © 1999, All Rights Reserved
phone toward the loudspeaker.
1.6. Adjust the loudspeaker volume so that a nominal dB SPL level based on Table 4
is registered at the microphone.
1.7. Use the L
EVEL
A
DJUST
buttons to adjust the channel input gain until 3 green and
1 yellow (or 0 dB) LED are lit on the I
NPUT
S
IGNAL
L
EVEL
M
ETER
.
1.8. Repeat steps 3 - 7 for all input channels.
1.9. Return all microphones to their normal operating location and orientation.
C
ALIBRATION
S
TEP
2: C
ALIBRATING
Z
ONE
O
UTPUTS
2.1. Once all input channels have been calibrated, press the A
UX
I
N
L
EVEL
/S
ETUP
button again to switch to Zone Output calibration. For Calibration Step 2, the
S
ETUP
LED will blink twice per period.
This step sets the nominal output level of the Zone Outputs to match your room
audio equipment. This step also lets you mark the maximum room loudspeaker
amplification level permissible without violating the room acoustic gain limit.
Note
.
It is vital to move the SPL meter and/or microphones so that each
microphone sees the correct dB SPL acoustic level as you are cal-
ibrating. Do not assume that because the first microphone sees
the dB SPL level, all other microphones will see the same level
(unless they are moved to occupy the same location as the first).
Note
.
Always double check the microphone level with normal speech
once the microphones are in normal operating position. Actual
speech levels may vary depending on room reverberation, etc.
Verify that you set a reasonable level (three green LEDs and one
solid yellow LED, or 0 dB) by actually talking and looking at the
meter.
Note
.
Use caution if the microphones lie in two acoustically separated
zones and you are only calibrating one zone. As you cycle through
microphones that lie in the other zone, no activity will be indicated
on the I
NPUT
S
IGNAL
L
EVEL
M
ETER
.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aspi EF1210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aspi EF1210 in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Aspi EF1210

Aspi EF1210 Additional guide - English - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info