736692
30
Zoom out
Zoom in
Previous page
1/48
Next page
30
Checking the blade
Warning
Wear or damage on the blades and the
fastening elements can result in the blades
or the fastening elements coming off.
Check the blades and all fastening ele-
ments according to the following instruc-
tions.
Warning
There is a considerable risk of injury due to
improperly mounted and maintained blades.
Work at blades must be carried out by an
authorised service centre.
Use solid gloves when you check
the blade.
Work on the blade requires specific expertise
because an imbalance inspection is necessary
and torques must be observed.
Blades that are sharpened improperly increase
the workload of the device and can result in vi-
bration cracks or breaks.
Check the blade and all fastening elements for
wear, damage and cracks
each time before and after you mow.
in case of noticeable changes or unusual vi-
brations.
Contact an authorised service centre if you de-
tect faults or damage during inspection.
All shown blade parts and their fastening ele-
ments must be changed
if damage or cracks are detected.
if unusually strong vibrations occur.
at least once a year or every 50 operating
hours, no matter if wear does exist or not.
The material weakens, can suffer cracks, en-
dangering people and material assets. Ejected
broken pieces can cause severe injuries.
Unusual vibrations are an indication that
blades are missing or broken,
the blade is worn excessively or on one side
or
damage to the engine or cutter deck fasten-
ing.
Changing the blade
1 1
1
1
2
2
3
3
4
6
55
Fig.10:
Cutting blades(5)
The cutting blades should move easily. To en-
sure this, always keep the pivotal point (3)
clean. Never mow when the cutting blades are
stuck.
Caution! To prevent unbalance replace or re-
verse the cutting blades in pairs only!
The cutting blades are reversing blades. Re-
verse both cutting blades
when one of the wear marks(1) was
reached.
when the second cutting edge of the cutting
blade has not been used yet.
It is absolutely necessary to change the cutting
blades and the fastening parts
when one of the wear marks(1) of the
second cutting edge was reached.
when the thickness of the cutting blade at
any point is below 1 mm (exception: cutting
edge).
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 940 Sherpa 4WD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 940 Sherpa 4WD in the language / languages: English as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 940 Sherpa 4WD

AS Motor AS 940 Sherpa 4WD User Manual - German - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info