736695
53
Zoom out
Zoom in
Previous page
1/60
Next page
Troubleshooting
53
Display Designation Reasons Remedy
C1 Microswitch transport posi-
tion does not switch
Fuse no. 5 (10A) has blown. Eliminate cause for triggering the fuse and
replace fuse.
Fuses nos. 1-3 (10A) have blown. Eliminate cause for triggering the fuse and
replace fuse.
Cutting height adjustment is blocked. Remove blockage.
C2 The blade switches off after
2minutes.
No activation of a control function in the
RC mode.
Engage the blade.
F1 Drive lever does not work
(RC)
Drive lever / rods blocked. Remove blockage.
Selection lever operating mode is not
completely set to RC.
Fold the selection lever operating mode all
the way.
Fuses nos. 1-3 (10A) have blown. Eliminate cause for triggering the fuse and
replace fuse.
F2 Drive lever does not move
to middle position (RC)
Drive lever / rods blocked. Remove blockage.
Fuses nos. 1-3 (10A) have blown. Eliminate cause for triggering the fuse and
replace fuse.
Selection lever operating mode is not
completely set to RC.
Fold the selection lever operating mode all
the way.
F3 Angle sensor driving Fuses nos. 1-3 (10A) have blown. Eliminate cause for triggering the fuse and
replace fuse.
F4 Steering does not work
(RC)
Steering is blocked by the ground. Steer in accordance with the ground proper-
ties.
Steering / rods blocked. Remove blockage.
Fuses nos. 1-3 (10A) have blown. Eliminate cause for triggering the fuse and
replace fuse.
Selection lever operating mode is not
completely set to RC.
Fold the selection lever operating mode all
the way.
F5 Angle sensor steering Fuses nos. 1-3 (10A) have blown. Eliminate cause for triggering the fuse and
replace fuse.
F6 Blade is not properly en-
gaged or disengaged
Fuse no. 5 (10 A) has blown. Eliminate cause for triggering the fuse and
replace fuse.
Fuses nos. 1-3 (10A) have blown. Eliminate cause for triggering the fuse and
replace fuse.
F7 Blade status unclear Fuse no. 5 (10 A) has blown. Eliminate cause for triggering the fuse and
replace fuse.
Fuses nos. 1-3 (10A) have blown. Eliminate cause for triggering the fuse and
replace fuse.
F8 Engine status unclear Engine status unclear, device is not safe
for operation.
Authorised service centre.
F9 Microswitch
Highest cutting height does
not switch
Fuse no. 5 (10A) has blown. Eliminate cause for triggering the fuse and
replace fuse.
Fuses nos. 1-3 (10A) have blown. Eliminate cause for triggering the fuse and
replace fuse.
Cutting height adjustment is blocked. Remove blockage.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 940 Sherpa 4 WD RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 940 Sherpa 4 WD RC in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 940 Sherpa 4 WD RC

AS Motor AS 940 Sherpa 4 WD RC User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info