736695

AS Motor AS 940 Sherpa 4 WD RC Manual

49
Zoom out
Zoom in
Previous page
1/60
Next page
Troubleshooting
49
Air filter is dirty. Maintain air filter (see Maintenance).
Spark plugs are dirty, damaged,
or incorrect electrode gap.
Clean spark plugs and check electrode
gap (see Maintenance). Replace spark
plugs if necessary.
Housing of the mower is
jammed.
See Maintenance.
No oil pressure:
Not enough engine oil.
Check engine oil level, refill.
No oil pressure:
Slope is too steep.
Bring the device to a level position.
Poor quality, dirty, or old fuel. Clean fuel system (authorised service
centre).
Always use fresh fuel.
Engine starts badly or
runs irregularly
Choke is closed. Open choke (see chapter Starting).
Air filter is dirty. Maintain air filter (see chapter Mainten-
ance).
Poor quality, dirty, or old fuel. Always use fresh fuel.
Spark plug is dirty, damaged, or
incorrect electrode gap.
Clean spark plug and check electrode
gap (see chapter Maintenance). Re-
place spark plug if necessary.
Engine stops during
mowing
No oil pressure:
Too little engine oil.
Check engine oil level, refill.
No oil pressure:
Slope too steep.
Move the device to a more level posi-
tion.
Device does not move RC mode:
Rotary knob limit speed is set to
“0”.
Adjust rotary knob limit speed.
The drive is unlocked. Lock the drive.
Hydrostatic drive is overheated. Cool down (see Maintenance).
Blade cannot be en-
gaged
The engine is not running. Start the engine
Move blade to transport posi-
tion.
Move blade to desired cutting position.
No oil pressure:
Too little engine oil.
Check engine oil level, refill.
No oil pressure:
Slope too steep.
Move the device to a more level posi-
tion.
MC mode:
Safety switches are not actu-
ated.
Move drive lever to neutral position.
Put driver in seat to activate seat contact
switches.
Insert the transmitter into the transmitter
holder.
Blade disengages
during mowing
No oil pressure:
Too little engine oil.
Check engine oil level, refill.
No oil pressure:
Slope too steep.
Move the device to a more level posi-
tion.
The blade does not
rotate
V-belt is insufficiently tensioned
or damaged.
Authorised service centre.
Bowden cable is defective. Authorised service centre.
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 940 Sherpa 4 WD RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 940 Sherpa 4 WD RC in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 940 Sherpa 4 WD RC

AS Motor AS 940 Sherpa 4 WD RC User Manual - German - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info