736673
19
Zoom out
Zoom in
Previous page
1/40
Next page
19
Starting
Warning
During startup, there is a risk of injury
caused by the rotating blade.
Make sure that no one is within the
danger zone of the blade. Do not tip the
device over to one side during startup.
Warning
Danger of poisoning due to poisonous ex-
haust gases.
Do not operate the engine in closed or
insufficiently ventilated rooms.
Please observe the safety instruction re-
garding the poisoning risk.
Warning
If after startup the carburetor does not close
properly, fuel will overflow and a fire hazard
occurs.
Close the fuel valve and contact an au-
thorised service centre.
AS 654TB&S and AS734TB&S
1. Place the device onto a flat surface, not in
high grass.
2. Open the fuel valve and the tank ventila-
tion.
3. Plug on the spark plug connector.
4. Set the engine stop switch to "I".
5. For cold start, set the accelerator switch to
position "choke"; otherwise, set it to me-
dium speed.
6. With your left thumb, press the start button
and continue to hold.
7. Pull the starter point slowly out until you
feel resistance then pull out quickly – en-
gine starts to run.
8. Let the starter rope retract slowly.
9. Release the start button.
10. For mowing, set the accelerator lever to the
maximum speed.
AS652TES
1. Place the device onto a flat surface, not in
high grass.
2. Open the fuel valve and the tank ventila-
tion.
3. Plug on the spark plug connector.
4. Only for cold start: Close the choke at the
carburetor (turn anti-clockwise).
5. Press the tickler at the carburetor until the
fuel is seen to drip.
6. Set the engine stop switch to "I".
7. Put the accelerator lever to lowest engine
speed position.
8. Pull the starter point slowly out until you
feel resistance then pull out quickly – en-
gine starts to run.
9. Let the starter rope retract slowly.
10. Put the accelerator lever to medium engine
speed position.
11. Reopen the choke (turn clockwise).
12. For mowing, set the accelerator lever to the
maximum speed.
Engaging the blade
1. Lift the blade clutch lever.
2. Press the latch knob at the blade clutch
lever.
3. Press the blade clutch lever towards the
handlebar – the blade starts to move.
Disengaging the blade when moving over
paths:
1. Release the blade clutch lever.
Setting the blade speed
Devices with blade speed lever
You will achieve a good result of cutting and
mulching with a high blade speed and medium
driving speed.
When the blade speed is low, the tractive
power of the blade is especially high and the
noise level lower.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AS Motor AS 73 4T B S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AS Motor AS 73 4T B S in the language / languages: English as an attachment in your email.

The manual is 1,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AS Motor AS 73 4T B S

AS Motor AS 73 4T B S User Manual - German - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info