702728
5
Zoom out
Zoom in
Previous page
1/12
Next page
- 5 -
10. TROUBLESHOOTING
Problem Possible cause Remedy
Operation LED does not light. 1. No power supply. 1. Turn on the power.
2. Bad wiring connection or broken wire (short). 2. Check and correct the wiring.
Alarm LED does not light when 1. No power supply. 1. Turn on th epower supply.
the beam is broken. 2. Poor wiring connection or broken wire (short). 2. Check and correct the wiring.
3. Beam is reflected on to another object and 3. Remove the reflecting object or change the beam
sent to the receiver. direction.
4. Two beams are not broken simultaneously. 4. Break two beams simultaneously.
5. The beam interruption time is shorter than the 5. Reduce the beam response time.
set response time.
Alarm LED continues to light. 1. Beam alignment is out. 1. Check and adjust again.
2. Shading object between the transmitter and 2. Remove the shading objects.
receiver. 3. Clean the optics with a soft cloth.
3. Unit optics are dirty. 4. Readjust to the same channel.
4. Frequency channel is not compatible between
the transmitter and receiver.
Intermittent alarms. 1. Bad wiring connection. 1. Check again.
2. Change of supply voltage. 2. Stabilize supply voltage.
3. Shading object between transmitter and 3. Remove the shading object.
receiver. 4. Change location of the installation.
4. A large electrical noise source, such as a 5. Stabilize.
power machine, is located near the transmitter 6. Clean the optics with a soft cloth.
and receiver. 7. Check and adjust again.
5. Unstable installation of transmitter and receiver. 8. Increase the response time. (impossible in a
6. Dirty transmitter or receiver optics. location where the intruder can run at full speed.)
7. Incorrect alignment.
8. Small animals may be passing through the
two beams.
11. SPECIFICATIONS
Model PB501 PB511 PB521
Detection system: Simultaneous breaking of 2 beams
Infrared beam: LED pulsed beam, double modulation
Protection distance: Outdoor 20 m or less Outdoor 40 m or less Outdoor 60 m or less
Indoor 40 m or less Indoor 80 m or less Indoor 120 m or less
Max. beam range: Outdoor 200 m or less Outdoor 400 m or less Outdoor 600 m or less
Indoor 200 m or less Indoor 400 m or less Indoor 600 m or less
Response time: 50-700 msec. (variable at pot)
Power supply: 12-30 VDC (non polarity)
Current consumption: 55 mA or less 75 mA or less 80 mA or less
Alarm output: Dry contact relay output form C
Contact action: interruption time + delay time (1-3 sec)
Contact capacity: 30 V AC/DC, 0.5 A or less
Tamper output: Dry contact relay 1b (N/C)
Action: activated when cover is detached
Contact capacity: 30 V AC/DC, 0.5 mA or less
Alarm LED: Red LED (receiver)
ON: when an alarm is initiated
Attenuation LED: Red LED (receiver)
ON: when a beam is attenuated
Functions: Beam frequency changeover (4 channels). Monitor jack output. AGC circuit. Frost-proof cover.
Ambient temperature change: -25°C to +60°C
Mounting positions: Indoor/outdoor
Wiring: Terminals
Weight: Transmitter: 380 g. Receiver: 400 g
Appearance: PC resin (wine red)
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech PB501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech PB501 in the language / languages: English, French, Swedish as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info