557702
16
Zoom out
Zoom in
Previous page
1/24
Next page
Page 16
User Manual for CD72/95/15003
D
ISARMING A SPLIT SYSTEM AFTER AN ALARM
The bells and the flashing light are activated when an alarm is triggered in the system. If your system
has the option, a report of the event is automatically sent over the phone lines to a central station. If
you inadvertently activate an alarm, immediately telephone the central station to prevent an
unnecessary response.
When you enter the premises after an alarm, the bell may already be silent if it has been so
programmed, but the red LED will still be activated. This allows there to be several alarms. Remember
to record the fault or alarm in your logbook for future reference.
If your code allows you to access more than one security area, you can select one of them to disarm.
1. Go to the keypad. The entry period starts as soon as you
open the entrance door, or when you enter the entry
zone. You can switch off the system without activating the
alarm as long as the beeping continues.
The red LED
ALARM
is lit on the keypad.
Beep Beep
The standby display is displayed. An example is shown.
TUE 23 APR 07.39
2. Press the key
0
and then enter your code. A ‘*’ appears in
the display for every key you press. Use the
0
key to
cancel an incorrect entry and to restart a new entry of the
code.
Enter Code
0 + code
Enter Code ****
In this example, the area 1 alarm has been triggered and
area 2 is armed.
Area 1 Alarm
Area 2 Armed
Enter Area No.
3. Enter the area number where the alarm occurred (in this
example it is 1). You have a few seconds to enter the
number.
1
Disarm?
4. Press the
Accept
key to disarm the selected area (area 1
in this example).
!
!!
!
A list of where the alarm was triggered is presented.
Events in Log...
In this example, the alarm was triggered in zone 4 ‘Back
Door’ on 23 April at 7.40am in area 1.
004 Alarm
004 Back Door
23 APR 05.20 A1
5. Press the
Accept
key to confirm the alarm.
!
!!
!
Area 1 Disarmed
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech CD 7203 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech CD 7203 in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info