702287
3
Zoom out
Zoom in
Previous page
1/20
Next page
3
Voice Reporting – No Acknowledge
Format No: 14
Burglar Alarm – Voice Message 0
Msg No:
Voice Reporting – Acknowledge
Format No: 13
1(a) Program the voice protocol in Communications Options
menu 19/9 for CS 1 to 4 with format No. 13 with
Acknowledge.
Or
1(b) Program the voice protocol in Communications Options
menu 19/9 for CS 1 to 4 with format No. 14 without
Acknowledge.
(Note: With Voice Reporting Format 13 (Acknowledge), the
receiver must confirm the message by pressing ‘0’ to
acknowledge the message. If the receiver does not confirm the
message, the message(s) will be repeated)
2 Map the recording voice message to one of the reporting
codes via menu 19/52. (Refer to table 2)
VOICE MESSAGE PROGRAMMING TABLE
Voice messages can be programmed to report on the
occurrence of specific reporting codes. More than 1 reporting
code may have the same voice message programmed.
Reporting codes 1-11 are general alarms, while reporting
codes 12-21 are zone specific, that is, you can program the
reporting codes to specific zones. The range is from 1-14.
Table 2
Reporting
code no.
Reporting code 1st ATS
7200
installed
Message
no.
2nd ATS
7200
installed
Message
no.
1 Burglar Alarm 1-6 1-14
2 Tamper Alarm 1-6 1-14
3 Hold-up Alarm 1-6 1-14
4 Panic Alarm 1-6 1-14
5 Fire Alarm 1-6 1-14
6 Medical Alarm 1-6 1-14
7 Technical Alarm 1-6 1-14
8 Mains Fail 1-6 1-14
9 DGP Offline 1-6 1-14
10 Area Disarmed 1-6 1-14
11 Area Armed 1-6 1-14
12 130 BA Burglary 1-6 1-14
13 131 BA Perimeter 1-6 1-14
14 132 BA Interior 1-6 1-14
15 133 BA 24 Hour 1-6 1-14
16 134 BA Entry/Exit 1-6 1-14
17 135 BA Day/Night 1-6 1-14
18 136 BA Outdoor 1-6 1-14
19 137 BA Tamper 1-6 1-14
20 138 BA Near Alarm 1-6 1-14
21 140 UA General Alarm 1-6 1-14
Note: Default message number 0 = No message
Attention: Reporting code 12 (130, BA Burglary) and reporting
code 1 (Burglar Alarm) are the same events. If reporting code
12 (130, Burglary) is programmed with an alarm message,
then this will override reporting code 1 (Burglar Alarm).
TECHNICAL SPECIFICATIONS
Power supply
12 V via ribbon cable from
control panel
Supply Current 50 mA
Recording capacity 8 messages (total recording
time – 35 sec.)
Recording bandwidth 3 kHZ
Dimensions 80 mm x 50 mm x 20 mm
Weight 123 gr.
Temperature 10°C to +50°C
Non-volatile memory Yes, temporary (min. 5
hours)
Automatic gain control
during recording
Yes
Acknowledge by DTMF code “0”
Module Vocal
QUE FAIT IL?
Le module ATS7200 permet de transmettre des messages pré
enregistrés vers 1, 2, 3 or 4 destinataires. La transmission du
protocole voix passe via le transmetteur intégré ou via le
module optionnel RNIS.
MODULE VOCAL UNIQUE OU MULTIPLE
Le nombre maximum de module vocal qui peuvent être
installés est de 2. Il y a 8 messages par module. Pour le
premier module nous avons en première position le message
d’introduction, en seconde position le message d’adresse et
ensuite 6 messages d’alarme. Si un second module vocal est
installé les 8 messages seront des messages d’alarme. (Voir
tableau 1 page 2)
IMPORTANT
Le module ATS7200 doit toujours être monté à l’intérieur du
coffret de la centrale.
Important:
1. Débrancher l’alimentation 220V avant d’ouvrir le coffret.
Débrancher la prise secteur du CA de la prise
murale.
OU
Couper l’alimentation secteur à l’aide du circuit de
protection dédié.
2. Déconnecter la batterie.
INSTRUCTION DE MONTAGE (REF. DESSINS & )
Placement du module ATS7200 dans le coffret centrale
(ATS2000/3000/4500)
1. Introduisez les attaches dans les orifices carrés (4)
(utilisez les entretoises métalliques ).
2. Montez le module ATS7200 en employant les vis.
Placement du module ATS7200 dans le coffret centrale
(ATS4000/2300/3300).
1. Retirez les vis (1) et enlevez le PCB de la centrale.
2. Placez les entretoises avec les bagues en plastique au-
dessus des entretoises existantes. (3).
3. Introduisez les attaches dans les orifices carrés (4).
4. Montez le module ATS7200 en employant les vis et les
entretoises. (5).
5. Remettez la centrale ATS en place.
Raccordement du module vocal
1. Branchez le câble plat (2) au connecteur J20 (CONN1 ou
CONN2).
2. Connectez la ligne téléphonique au transmetteur intégré
ou au module RNIS.
F
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech ATS7200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS7200 in the language / languages: English, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info