702287
2
Zoom out
Zoom in
Previous page
1/20
Next page
2
Voice Reporting
Module
WHAT DOES IT DO?
The ATS7200 enables event reporting by playing back pre-
recorded messages to 1, 2, 3 or 4 different reporting sites
(Central Stations). Voice reporting takes place via the built-in
dialer of the control panel (PSTN) or via the optional ISDN
module.
SINGLE AND MULTIPLE VOICE MODULE MESSAGES
A maximum of 2 voice reporting modules can be installed.
There are 8 messages per module; the leader message, the
address message and 6 alarm messages. If a second module
is installed, all 8 messages for the second module will be
alarm messages (Refer to table 1 on page 2)
MOUNTING LOCATION
The ATS7200 must be mounted inside an ATS panel housing.
Important:
1. Disconnect the mains power before opening the cabinet.
Disconnect AC mains plug from AC mains wall
socket.
OR
Disconnect the mains with a dedicated circuit
breaker.
2. Disconnect the battery (when applicable).
MOUNTING THE UNIT (REF. TO FIGURE & )
Mounting the ATS7200 into the control panel
(ATS2000/3000/4500)
1. Place the clips in the square holes (4) (use metal pillars
when available).
2. Mount the ATS7200 using screws.
Mounting the ATS7200 into the control panel
(ATS4000/2300/3300).
1. Remove the screws (1) and lift off the control panel PCB.
2. Place the extension pillars with the plastic rings on top of
the existing pillars (3).
3. Place the clips in the square holes (4).
4. Mount the ATS7200 using the screws and extension pillars
(5).
5. Place the ATS control panel PCB back into it’s original
position.
Connecting the voice module
1. Connect the flat cable (2) between the control panel
(connector J20) and the ATS7200 (connector CONN1or
CONN2).
2. Connect the telephone line to the control panel or to the
ISDN module.
DESCRIPTION OF THE ATS7200 (REF. TO FIGURE )
No. Description Function
1. CONN 1/CONN 2
(System connector)
Communicates between the
ATS7200 and the main
panel.
2. CONN 3 Used for recording and
checking messages.
3. Push button Controls recording and
checking of reporting
messages.
4. Jumpers Selects additional slave
addresses in the event that
more than one voice
reporting module is used
within the same panel.
5. Gold Cap Used for retaining recorded
messages during short
power failures.
6. LED Indicates presence of +12
VDC power.
MI ADDRESS SELECTION AND POSITIONING JUMPERS
The address of the ATS7200 on the MI-bus is determined by
three jumpers. These jumpers are placed beside the Gold cap
and are labelled A0, A1 and A2. If only one module is used, all
jumpers will be present. For the second module, jumper A0 will
be removed.
Note: Jumpers A1 and A2 are for future applications
Device Jumpers
A0 A1 A2
Module 1 I I I Default I = Inserted
Module 2 R I I R = Removed
REPORTING SEQUENCE
The ATS7200 first reports the leader message (1) followed by
one or more of the alarm messages (3 to 8) and finally the
address message (2). The leader message is repeated up to
10 times unless the user presses “0” to move over to the
actual alarm message. If the user does not press zero in time,
the panel hangs up and dials again later. When a second
ATS7200 is installed, all 8 messages of the second unit are
alarm messages. Therefore messages 3 to16 will be available
for alarm messages. (Note: The total recording time for the
eight messages is 35 sec.).
Table 1
Position Function Examples
Message1
(Leader
message)
Notifies the listener
that a voice report
message is waiting
by playing back a
number of times.
"There is an alarm.
Press ‘0’ (zero) for
details."
Message 2
(Address
message)
Specifies the
address of the
protected premises.
“….At Interlogix,
Kelvinstraat,
Weert”. Press ‘0’
(zero) to
acknowledge this
message”.
Message 3-8
(Alarm
message 1-6)
Reports different
alarm types (They
can be played back
to any MI-audio
lines
“Burglary, Front
door”.
“Tamper”
“Mains Fail”
TO RECORD A MESSAGE (RECORD MODE):
1. Prepare a list of messages before starting recording. Use
the programming sheets in tables 3 and 4.
2. Turn on the power (reconnect the mains and the battery)
and connect the telephone to CONN 3.
3. Pick up the handset of the programming telephone and
put it to your ear.
4. Press the push button next to the RJ12 connector, wait
for the beep, and start speaking.
5. Release the button only after you have finished recording
the message. (Note: In case of a mistake, release the
button for more than 10 seconds or press for less than 1
second to reset the programme and start recording
again.)
6. To record the next message, press the button again
within the 10 second time-out and speak again after the
beep.
7. Repeat steps 3 and 4 until you have recorded all 8
messages.
PLAYBACK THE RECORDED MESSAGES (CHECK MODE):
1. Press the push button for less than one second.
(Important: If it is pressed for more than 1 second, you
go back into programming mode.)
2. Listen to the messages that you have been recorded.
Attention: At the end of either Record mode or Check
mode, there will be 7 beeps to indicate that the module is
now available for event reporting.
PROGRAMMING THE ADVISOR MASTER
After recording the messages, program the Advisor Master by
selecting the Voice protocol for 1 to 4 Central Stations (CS).
GB
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech ATS7200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS7200 in the language / languages: English, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info