702286
10
Zoom out
Zoom in
Previous page
1/24
Next page
10 ATS7100/7110 Installation and Troubleshooting Guide
LED LED 1 –
Status
LED 2 - Call
Status (B-
channel)
LED 3 - X25
Call Status
1
Off Hardware
failure
Offline Offline
Flash Operational
2
Call setup in
progress
2
Call setup in
progress
2
Blink Local S0 bus
failure
Incoming call
present
Pause
before
reconnect
On Line fault,
network
failure
Online Online
Table 2. ATS71xx status LEDs
Notes:
1
ATS7110 only
2
A running light on all the three leds indicates the unit
is initialising.
2.5. Programming the ATS7100
The minimum programming settings for the ATS7100
are:
Menu Description Comments
19.9 Reporting format Per Central Station
19.9 Phone number 1 Per Central Station
19.9 System account
number
Per Central Station
19.9 Area account number Per Central Station
and Area
19.9 Select ISDN dialler Per Central Station
19.9 Connection type 1 – ISDN
Per Central Station
For Panel firmware
V04.00.00 and
higher
Table 3. ATS7100 minimum settings
For further programming details see the ATS
2000/3000/4000/4500 programming manual.
2.6. Programming the ATS7110
The minimum programming settings for the ATS7110
are:
Menu Description Comments
19.9 X25 TEI value Belgium: 1
Netherlands: 2
19.9 X25 D-Bit Belgium: No
Netherlands: Yes
19.9 Reporting format X25 ENAI
Per Central Station
19.9 Phone number 1 Per Central Station
19.9 System account
number
Per Central Station
19.9 Area account number Per Central Station
and Area
19.9 Select ISDN dialler Per Central Station
19.9 X25 Account Code Per Central Station
19.9 Connection type 2 – ISDN-D
Per Central Station
For Panel firmware
V04.00.00 and
higher
Table 4. ATS7110 minimum settings
For further programming details see the ATS
2000/3000/4000/4500 programming manual.
Using Titan
In general no events will be reported to the Central
Station while Titan is on-line to the panel. Due to
shared resources some limitations apply when
connecting Titan to a system to which an ATS7110 is
connected.
When Titan is used via J18 using the
ATS1830/ATS1834 cable, no events can be
reported via D-Channel X25 as long as the cable is
connected. Disconnect cable from panel when
ready.
Start a local J18 Titan connection by typing
*<installer code>Enter, select menu 7. Do not
select installer menu 19, since doing so initiates
the transmission of the LB event. When the
ATS1830/ATS1834 cable is already connected, the
ATS7110 will not be able to transmit this event,
and both event reporting and Titan are blocked.
2.7. Line monitor/guard (ATS7100
and ATS7110 in B-channel
mode)
The line monitor is activated by setting the menu
“Activate ISDN line monitor” to “YES” (see menu 9). If
enabled, the ATS7100/7110 ISDN checks whether the
S0 bus is activated or not. If the S0 bus is not activated,
it will initiate an activate request to the network and wait
for 12 seconds for the S0 bus to be activated. If there is
no response from the network, the ATS7100/7110
ISDN disconnects the outgoing S0 bus (CONN4) from
the network by its internal relay and initiates another
activate request to the network.
If there is still no response, the network has failed. The
ATS7100/7110 ISDN will then report a line fault to the
panel. The outgoing S0 bus was probably not the cause
of the line fault and will therefore be re-connected to the
network. The ATS7100/7110 ISDN keeps trying to
activate until the network is back.
However, if the network does respond after
disconnecting the outgoing S0 bus (CONN4), the
outgoing S0 bus caused the line fault. The
ATS7100/7110 ISDN keeps the outgoing S0 bus
disconnected to ensure proper operation. From then on
it will reconnect the outgoing S0 bus every hour to test
whether the S0 bus problem has been solved or not.
This state will be remained until the S0 bus is
operational. As it is still possible to transmit alarm
events, there will be no line fault reporting to the panel.
2.8. Troubleshooting
LEDs indicating operation/trouble mode (see table
4 and 5).
Speaker connector
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech ATS7100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS7100 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info