702278
9
Zoom out
Zoom in
Previous page
1/36
Next page
Menu 15, Factory Defaults
This option allows you to reset the Wireless DGP to its factory
default settings (extended mode, 16 zones). Resetting clears the
entire Wireless DGP database.
Testing
Test the receiver module at the desired location to evaluate
performance in the particular environment.
Verify that the RF/Power LED flashes when wireless devices
are activated.
Perform the tests according to menus 1 and 5.
For other configuration, refer to the ATS Quick Programming
and Installation guide.
For Installation troubleshooting see page 9.
Installation troubleshooting
Problem Action/Solution
The Wireless DGP
module RF/Power
stays off when
power is applied.
Check for incorrect wiring connections.
Make sure the ATS control panel is
powered correctly.
Measure Wireless DGP DC power with a
multimeter (should be 13.8 VDC).
If the LED still remains off, replace the
Wireless DGP module.
The Wireless DGP
module RF/Power
LED stays lit but
doesn’t
flash when
wireless devices
are activated.
Check for Wireless DGP antenna proximity
to metal obstructions, such as ducting or
AC wiring.
Make sure the sensor transmitters are the
correct frequency, that is, 868 MHz FM.
If LED still doesn’t flash, replace the DGP.
The Wireless DGP
RF/Power LED
stays lit
and flashes when
wireless devices
are activated, but
ATS control
doesn’t respond.
Check that DIP switch address 0 is not
selected on the DGP.
Check Wireless DGP databus connections.
Check that each Wireless DGP connected
to the databus has a unique address.
Check that the Wireless DGP is being
polled by (ATS control Menu 19 > 4.)
Check that the transmitter sensor is
programmed into the Wireless DGP. See
Programming Guide.
Check if daughterboard is mounted
properly to motherboard.
If the ATS control system still doesn’t
respond, try replacing the Wireless DGP
module.
Technical specifications
Compatibility ATS control panels: ATS4xxx, ATS30xx,
ATS20xx, ATS10xx
Version 04.05.10 or later, the optimal is
04.08.xx or later
GE Security 868 MHz FM (crystal and SAW)
Learn Mode wireless sensors
Wireless zones 16 or 32 per Wireless DGP (Programmable)
Power required 12 VDC nominal (13.8 V max)
100 mA maximum
Maximum
recommended
bus distance
1500 m using WCAT52/54, 2-pair twisted,
shielded data cable.
Storage
temperature
-33 to +60°C
Operating
temperature
0 to +60°C
Maximum
humidity
90% relative humidity, non-condensing
Wireless signal
range
300 m typical open air
May vary with application
Dimensions 16.5 x 12 x 3.5 cm (L x W x H), excluding
antenna
With antenna 23.5 cm
The European directive "Waste Electrical and Electronic Equipment"
(WEEE) aims to minimise the impact of electrical and electronic
equipment waste on the environment and human health. To
conform with this directive, electrical equipment marked with this
symbol must not be disposed of in European public disposal
systems. European users of electrical equipment must now return
end-of-life equipment for disposal. Further information can be found
on the following website: www.recyclethis.info.
FR
ATS123
4
DGP radio 868 MHz FM
Introduction
Le récepteur DGP radio ATS1234 étend la capacité d’entrée
de la centrale ATS jusqu’à 32 zones au moyen des détecteurs-
transmetteurs radio Learn Mode™ 868 MHz (cristal ou SAW).
Le DGP ATS1234 nécessite une centrale ATS version 04.05.10 ou
supérieure. Les fonctionnalités complètes et conformités de
l'ATS12340 sont disponibles uniquement sur les centrales version
04.08.xx ou supérieure.
Ce module introduit un nouveau concept de carte mère et fille. Ce
concept permettra dans le futur de pouvoir utiliser différentes
fréquences en remplaçant uniquement la carte mère.
Il est possible de connecter jusqu’à 15 DGP à la centrale
ATS, à condition de réunir 240 zones radio (également
désignées sous le terme d’entrées) ou jusqu’à
240 télécommandes pour armer/désarmer une surface ou
activer/ désactiver des contrôles relais.
La longueur maximum recommandée pour le bus de
données est de 1500 m lorsque au moins un DGP radio
ATS1234 est connecté.
Le DGP radio exploite la diversité spatiale pour réduire au
minimum les " points morts " ou les absences de signal, et
sa portée de réception nominale en plein air est de 400 m.
Pour éliminer les points morts, utiliser un répéteur 868 MHz.
Il est possible d’alimenter le DGP radio au moyen de
l’alimentation du bus de données de la centrale ATS
ou d’une alimentation auxiliaire distante.
Des boutons de télécommande peuvent être programmés
afin de permettre aux utilisateurs d’armer/désarmer le
système ou de contrôler des relais ; par exemple, ouvrir
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech ATS1234 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS1234 in the language / languages: English, Dutch, Danish, French, Italian, Finnish as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info