Manual Aritech ATS1197 (page 3 of 8) (English)

702273

Zoom out

Zoom in

1/8

between 5 – 14V

Yellow Not used

Red Not used

NOTE: In off-line mode, the TERM switch (DIP switch 5) must be ‘off’

(up). DIP switches 1 to 4 are not used in off-line mode.

OPERATING FEATURES

Night Light

The reader will be dimly lit when enabled.

Beeper tone

Press and hold the * key while pressing the 1 key to raise the tone

frequency or the 2 key to lower the tone frequency.

POWER UP

Upon initial power up, the buzzer will sound two beeps indicating that

the internal non-volatile memory is OK. All of the area LEDs may

illuminate indicating that the system is armed. All areas must be

disarmed in order to enable access to the installer programming

menu options.

TROUBLESHOOTING

General Faults

No LED display or keypad backlight:

• Verify the +13.8 and 0V wire connections on both the RAS and

the power supply.

• Verify power output on the control panel, 4-door controller, or

external power supply.

All three status LEDs are flashing:

• Verify the D+ and D- wire connections (may be reversed or

open circuit).

• Verify the address DIP switches of the RAS are set to the

proper address.

• Verify that the control panel or 4-door controller is polling the

RAS address.

The RAS does not respond to a Smart Card:

• The RAS may not be programmed correctly or card beep and

LED flash may be disabled. Refer Programming for details.

• The Smart Card may not be programmed for use with the

particular system.

RX and TX LED Indications

RX and TX LEDs are provided on the circuit board to assist in fault

diagnosis and are visible when the rear plastic cover is removed.

Rx The yellow Rx LED flashes to indicate polling data is being

received on the system bus from the panel. If the LED does

not flash, the control panel is not operational or the bus is

faulty (usually cabling).

Tx The red Tx LED flashes to indicate the RAS is replying to

polling from the control panel. If the Rx LED flashes but the

Tx LED does not, the RAS is not programmed to be polled

in the control panel or is addressed incorrectly

CONFIGURING THE ATS 1197 RAS

To Configure the RAS:

• Press 19 [ENTER] followed by * 3 [ENTER.

• Type the requred RAS address (2 – 16). followed by [ENTER].

• Select the RAS.

• Disable the option ’LCD Arming Station’.

• Enable the option ‘3 LED RAS’.

PROGRAMMING MAP

2-LEDs off-line

0-Exit, Menu:

GE Security, RAS1197.V01

0-EXIT, Menu:

Two wire Led Control

*-Change, #-Exit

3-Valid Card Flash

0-Exit, Menu:

Enabled

*-Change, #-Exit

4-Night Light

0-Exit, Menu:

Enabled

*-Change, #-Exit

6-Card Beep

0-Exit, Menu:

Enabled

*-Yes, #-No

7-Watch Dog

0-Exit, Menu:

Disabled

*-Change, #-Exit

8-O/C Output

0-Exit, Menu:

Door Output

*-Change, #-Exit

9-Option Card

0-Exit, Menu:

Enabled

*-Change, #-Exit

10-RTE (Egress)

0-Exit, Menu:

RTE Disabled

*-Change, #-Exit

11-Factory Defaults

0-Exit, Menu:

Set Defaults?

*-Yes, #-No

5-Protocol Options

0-Exit, Menu:

Wiegand

*-Change, #-Exit

13-Last Card

0-Exit, Menu:

00,00,00,00,00,00

#-Exit

16-Security Mode

0-Exit, Menu:

Un-Secured Mode

*-Change, #-Exit

Note: Reserved menus are not shown

PROGRAMMING OPTIONS

The ATS1197 provides for a menu through which a number of

options can be set.

To enter the programming menu for the ATS1197:

• Enter menu 28 of the Control Panel installer menu.

• Press 2[ENTER] followed by the RAS address selected and

[ENTER] to enter the RAS menu. The display now shows “GE

Security, RAS1197” followed by the version number.

• Press [ENTER] to proceed to the menu or press the menu

number followed by [ENTER] to go to a menu item directly.

Menu 1, 12, 14 and 15 are reserved menu’s.

Menu 2, LEDs off-line

Select either two-wire (default) or one-wire LED control.

For two-wire LED control:

• The brown wire controls LED 1 red (Arm). Wire grounded: LED

1 red on, wire open or at +5 V to +14 V: LED 1 off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Aritech ATS1197 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Aritech ATS1197 Manual

Product: