702741

Aritech AD044 Manual

3
Zoom out
Zoom in
Previous page
1/10
Next page
3
2. If Inputs 2,3 or 4 or even 5, 6, 7 and 8 are used, they
must be within the ATS1290 I/O range. If they are out
of range, they are not available.
3. If some AD044 inputs are not used, the linked zone
input in the ATS control panel must be programmed
as disabled (default).
4. If some AD044 outputs are not used, the linked output
in the ATS control panel must not be programmed
(default).
Refer also to the ATS1290 manual for the direct link to the
zone number (control panel).
MEMORY LOCATION MAP
Every PID device has its own characteristics concerning
related I/O lines or certain functionality of the device.
A total of 16 memory locations are reserved to configure
the PID devices. Only the first nine are normally user
configurable. This depends on the functionality of the
particular device.
For the AD044 external PID interface only memory locations
3 and 5 matter.
On Memory Location 3, the zone type can be configured for
each input to Single EOL, Double EOL (default) or the zone
can be switched off (the status will always be “Normal”).
On Memory Location 5, the output supervision can be
enabled (default) or disabled for each output.
MEMORY LOCATION MAP FOR AD044
Location Function Decimal values Binary values
3 Zone types
For example:
0 = All zones are Off
85 = All zones are Single EOL
170 = All zones are Double EOL (default)
Zone 4 Zone 3 Zone 2 Zone 1
Bit 7-6 Bit 5-4 Bit 3-2 Bit 1-0
00 = Zone is Off
01 = Single EOL
10 = Double EOL (default)
11 = Undefined
5
Supervision
outputs
For Example:
0 = All Output Supervisions disabled
15 = All Output Supervisions enabled (default)
Output 4 Output 3 Output 2 Output 1
Bit 3 Bit 2 Bit 1 Bit 0
0 = Disabled
1 = Enabled (default)
ZONE TYPE
Input loop
resistance
Status ATS control panel
Double EOL
Status ATS control panel
Single EOL
<20 ohm Short Short
47K Normal Normal
94K Alarm Open
> 1Meg ohm Open Open
TECHNICAL SPECIFICATIONS
Bus protocol.........................................GE Interlogix Point ID
Bus voltage........................................................ 12 V or 24 V
External power supply ...................12/24 V (see Note below)
Current consumption from bus ...................................290 µA
Unit load for DGP ................................................................ 1
Address range .......................................................... 0 to 255
Max Current Outputs ......................................500 mA (each)
Single EOL resistor Inputs ................................ 47 kΩ +/- 5%
Double EOL resistors Inputs........................2 x 47 kΩ +/- 5%
EOL resistors Outputs ................................................. 47 KΩ
Category........................................................................... I/O
Device type........................................................................ T1
Note: The auxiliary power output of closest panel or DGP can
also be used.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Aritech AD044 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Aritech AD044 in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 0,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info