Manual Ariston PO 740 ES IX (page 15 of 70) (English, German, Dutch, French, Italian, Portuguese, Spanish)

455092

Zoom out

Zoom in

1/70

independent, not only for safety purposes, but also to

facilitate removal of one or both in the future.

Electrical Connection for Gas Cooktop

Fit the supply cord with a standard plug for the demand rate

indicated on the rating plate or connect it directly to the

electrical mains. In the latter case, a single pole switch must

be placed between the appliance and the mains, with a

minimum opening between the contacts of 3 mm in

compliance with current safety codes (the earthing wire must

not be interrupted by the switch). The power supply cord

must be positioned so that it does not reach a temperature

in excess of 50°C above room temperature at any point.

Before making the actual connection, make sure that:

• The fuse and electrical system can withstand the load

required by the appliance;

• That the electrical supply system is equiped with an

efficient earth hook-up according to the norms and

regulations prescribed by law;

• That the plug or switch is easily accessible.

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the wires in the mains lead may not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

Connect the Green & Yellow wire to the terminal marked “E”

or or coloured Green or Green & Yellow.

Connect the Brown wire to the terminal marked “L” or coloured

Red.

Connect the Blue wire to the terminal marked “N” or coloured

Black.

Adapting the Cooktop for Different Types of Gas

To adapt the cooktop to a different type of gas than that for

which it was designed, (see the sticker under the hob or on

the packaging), the burner nozzles must be changed, as

follows:

• Remove the pan supports and slide the burners out of

the cooktop.

• Unscrew the nozzles using a 7mm socket wrench and

replace them with those for the new type of gas. (See

table 1, “Burner and Nozzle Specifications”).

• Reassemble the parts following the instructions in reverse

order.

• On completing the operation, replace the old rating label

with the one showing the new type of gas; the sticker is

available from our Service Centres.

If the gas pressure is different than that prescribed, a pressure

regulator must be installed at the source, in compliance with

national standards governing the use of piped gas regulators.

Regulation of Air Supply to the Burner

The burners do not need a primary air regulator.

Minimum Regulation

• Turn the gas valve to minimum.

• Remove the knob and turn the regulator screw (positioned

either on the side of the top or inside the shaft) clockwise

until the flame becomes small but regular.

N.B.: In the case of liquid gas, the regulation screw must be

fully screwed in (clockwise).

• Make sure that, when the knob is turned rapidly high to

low, the flame does not go out.

• In the event of a malfunction on appliances with the

security device (thermocouple) when the gas supply is

set at minimum, increase the minimum supply levels using

the regulator screw.

Once the adjustment has been made, apply sealing wax, or

a suitable substitute, to the old seals on the by-pass.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ariston PO 740 ES IX in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ariston PO 740 ES IX Manual

Product: