566471
43
Zoom out
Zoom in
Previous page
1/104
Next page
Heat pump water heater – OPERATING AND MAINTENANCE INSTRUCTIONS
43
For example, when leaving home on a Saturday morning to return on the Sunday of the successive week, on
Saturday morning it will be necessary to programme 7 nights of absence so as to have hot water available upon
returning home on Sunday. To stop this function press the button “mode”.
7.5 Time setting
The time setting is required if:
Program mode has been enabled by the installer menu (P11 parameter set to ON, see
section 7.7);
The Program is activated and occur simultaneously absence of power from the mains and
battery (the product will restart in Auto mode).
You can also change the current time through the parameter L0 (paragraph 7.6).
The display flashes up showing hours and minutes. Turn the knob until you find the current
time and confirm by pressing the knob. Repeat the procedure to set the minutes.
7.6 Information menu
The information menu allows for 43isualize4343 data for monitoring the product. To enter
the menu, press the relative knob and hold for 5 seconds.
Turn the knob to select the parameters L1, L2, L3 … L14.
The description of the parameter appears on the line below.
Upon reaching the desired parameter, press the knob to 43isualize its value. Press the knob
or “MODE” button to return to the parameter selection area once again.
To exit the information menu, press the “mode” button (the appliance will ensure that the menu is
automatically exited after the latter has been idle for 10 minutes).
Parameter
Name
Parameter description
L0 TIME
Visualization and setting of the current time (changeable parameter, available only if
“Program” mode is activated).
L1
HCHP
Activated/deactivated st
atus of the two
-
tier rate operation mode.
L2
TIME_W
Maximum accepted hours of powering.
L3
ANTI_B
Activated/deactivated status of the anti
-
legionnaire’s disease function (on/off).
L4
T HP
Maximum pre
-
set temperature of the pump assembly.
L5
T W1
Tempe
rature recorded by the heating element unit sensor 1.
L6
T W2
Temperature recorded by the heating element unit sensor 2.
L7
TW3
Temperature recorded by the hot water pipe sensor.
L8
T AIR
Temperature recorded by the inlet air sensor.
L9
T EVAP
Temperat
ure recorded by the evaporator sensor.
L10
DEFROS
Activated/deactivated status of the defrost function (on/off).
L11
HP h
Meter for internal parameter 1.
L12
HE h
Meter for internal parameter 2.
L13
SW MB
Mainboard software version.
L14
SW HMI
Interfa
ce board software version.
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston NUOS 200 SPLIT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston NUOS 200 SPLIT in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 2,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info