719964
9
Zoom out
Zoom in
Previous page
1/64
Next page
/ 9
INSTALLATION
Reference Standards
In the United Kingdom, the installation and initial start-up of the
boiler must be by a Gas Safe registered installer in accordance with
the installation standards currently in effect, as well as with any and
all local health and safety standards i.e. Gas Safe.
In the Republic of Ireland the installation and initial start-up of the
appliance must be carried out by a Competent Person in accordance
with the current edition of I.S.813 “Domestic Gas Installations and
the current Building Regulations, reference should also be made to
the current ETCI rules for electrical installation.
The installation of this appliance must be in accordance with
the relevant requirements of the Local Building Regulations, the
current I.E.E. Wiring Regulations, the by-laws of the local authority,
in Scotland, in accordance with the Building Standards (Scotland)
Regulation and Health and Safety document No. 635, “Electricity
at Work Regulations 1989” and in the Republic of Ireland with the
current edition of I.S. 813 and the Local Building Regulations (IE).
C.O.S.H.H.
Materials used in the manufacture of this appliance are non-
hazardous and no special precautions are required when servicing.
Codes of Practive
Installation should also comply with the following British Standards
Code of Practice:
BS 7593: Treatment of water in domestic hot water
central heating systems
BS 5546: Installation of hot water supplies for
domestic purposes
BS 5440-1: Flues
BS 5440-2: Air supply
BS EN 12831 - BS EN 14336:
Forced circulation hot water systems
BS 6798: Installation of gas fired hot water boilers
of rated input not exceeding 70kW
BS 6891: Installation of low pressure gas pipes up to 28mm
BS 7671: IEE Wiring Regulations
BS 4814: Specification for expansion vessels
BS 5482: Installation of L.P.G.
Technical Bulletin TB143 Flue Gas Analysis
and in the Republic of Ireland in accordancce with the following
codes of practice:
I.S. 813 Domestic Gas Installations
Avoid installing the boiler where the air inlet can be polluted
by chemical products such as chlorine (swimming pool area), or
ammonia (hair dresser), or alkalin products (launderette).
Flue
Detailed information on flue assembly can be found in the
Connecting the Flue section.
The boiler must be installed so that the flue terminal is exposed to the
free passage of external air at all times and must not be installed in
a place likely to cause nuisance. It must not be allowed to discharge
into another room or space such as an outhouse or closed lean-to.
Condensing boilers have a tendency to form a plume of water
vapour from the flue terminal due to the low temperature of
the flue gasses. The terminal should therefore be located with
due regard for the damage or discolouration that may occur to
building within the vicinity and consideration must also be given to
adjacent boundaries, openable windows should also be taken into
consideration when siting the flue.
The minimum acceptable clearances are shown below:
- A Directly below an opening, window, etc 300 mm
- B Horizontally to an opening, window, etc 300 mm
- C Below gutters, soils pipes or drain pipes 75 mm
- D Below eaves 200 mm
- E From vertical drain pipe or soil pipe 75 mm
- F From internal or external corner 300 mm
- G Above ground, roof or balcony level 300 mm
- H From a surface facing the terminal 600 mm
- I From a terminal facing a terminal 1200 mm
- J Vertically from a terminal on the same wall 1500 mm
- K Horizontally from an terminal on the same wall 300 mm
- L Fixed by vertical flue terminal
Note: the flue must Not be iNstalled iN a place likely to cause a NuisaNce
aNd positioNed to eNsure that products of combustioN do Not discharge
across a bouNdary
It may be necessary to protect the terminal with a guard, if this is the
case it will be necessary to purchase a stainless steel terminal guard.
Reference should be made to the Building Regulations for guidance.
Ventilation
The room in which the boiler is installed does not require specific
ventilation. If the boiler is installed in a cupboard or compartment
ventilation is not required for cooling purposes.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ariston Clas HE R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ariston Clas HE R in the language / languages: English as an attachment in your email.

The manual is 16,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info