689099
11
Zoom out
Zoom in
Previous page
1/32
Next page
V 03/17
43
9. SLEEP button
In cool, heat or dry mode, press this button to start the SLEEP function. The icon will
appear on the remote control display. Press the button again to exit the SLEEP function. The
icon will disappear from the display.
The temperature will increase or decrease by 2 degrees over two hours according to the
function selected (cool/heat).
10. TEMP button
Pressing this button will allow you to display the set temperature, the indoor ambient
temperature, or the outdoor ambient temperature on the indoor unit's display. You can cycle
through the settings on the remote control display as shown below:
nessuna
visualizzazione
nessunavisualizzazione nodisplay
When you select or “no display” with the remote control, the set temperature will appear
on the indoor unit's display.
When you select
with the remote control, the indoor ambient temperature will appear on
the indoor unit's display.
When you select
with the remote control, the outdoor ambient temperature will appear
on the indoor unit's display.
N.B.:
It is not possible to display the outdoor ambient temperature on all models. The indoor unit
will receive the
signal but will display the set temperature.
The set temperature will appear on the unit's display on start-up, if enabled to do so.
When you select to display the indoor or outdoor ambient temperature, the indoor unit will
display the corresponding temperature for three to five seconds, after which it will
automatically revert to displaying the set temperature.
11. TIMER ON button
SETTING TIMER ON
This function allows you to program the air conditioner to turn on. When you press this button,
the
icon will disappear from the display and the word "ON" will flash on the remote control
display. Press "▲" or "▼" to adjust the TIMER ON setting.
Press and hold "▲" or "▼" for 2 seconds to rapidly change the time until you reach the desired
value. Press TIMER ON to confirm. The word "ON" will stop flashing. The
icon will re-
appear on the display.
CANCELLING TIMER ON
If the TIMER ON function is enabled, press the TIMER ON button to cancel the setting.
12. CLOCK button
Press this button to set the clock. The icon will flash on the remote control display. Press
"▲" or "▼" within 5 seconds to set the clock. Each time you press "▲" or "▼", the clock will
increase or decrease by 1 minute. Press and hold "▲" or "▼" for 2 seconds to rapidly change
the time. Release the button when you reach the desired time. Press "CLOCK" to confirm the
time. The
icon will stop flashing.
N.B.:
• The time displays in the 24-hour clock format.
• If no adjustment is made for 5 seconds the remote control will exit the setting mode. This also
applies to the TIMER ON/OFF function.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo X3MI 80 SH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo X3MI 80 SH in the language / languages: English as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info