665464
10
Zoom out
Zoom in
Previous page
1/30
Next page
V 11/15
40
7. SLEEP button
In cool, heat or dry mode, press this button to start the SLEEP function. The icon will appear
on the remote control display. Press the button again to exit the SLEEP function. The
icon will
disappear from the display.
8. TEMP button
Pressing this button will allow you to display the set temperature, the indoor ambient
temperature, or the outdoor ambient temperature on the indoor unit's display. You can cycle
through the settings on the remote control display as shown below:
nessuna
visualizzazione
nessunavisualizzazione no display
When you select or “no display” with the remote control, the set temperature will appear
on the indoor unit's display.
When you select
with the remote control, the indoor ambient temperature will appear on
the indoor unit's display.
When you select
with the remote control, the outdoor ambient temperature will appear on
the indoor unit's display.
N.B.:
It is not possible to display the outdoor ambient temperature on all models. The indoor unit
will receive the
signal but will display the set temperature.
The set temperature will appear on the unit's display on start-up, if enabled to do so.
• When you select to display the indoor or outdoor ambient temperature, the indoor unit will
display the corresponding temperature for three to five seconds, after which it will
automatically revert to displaying the set temperature.
9. I FEEL button
Press this button to start the I FEEL function. The icon will appear on the remote control
display. When you select this function, the remote control will send the detected ambient
temperature to the indoor unit, which will then adjust its operation automatically based on the
difference between the detected temperature and the set temperature.
Press the button again to exit the I FEEL function. The
icon will disappear from the display.
The remote control should be positioned near the user when this function is selected. The
remote control should not be placed anywhere high or low temperatures may occur to
avoid inaccurate ambient temperature detection.
10. LIGHT button
Press this button to turn off the indoor unit's display light. The icon will disappear from the
remote control display.
Press this button again to turn on the display light. The
icon will appear on the display.
11. CLOCK button
Press this button to set the clock. The icon will flash on the remote control display. Press ""
or "" within 5 seconds to set the clock. Each time you press "" or "", the clock will increase
or decrease by 1 minute. Press and hold "" or "" for 2 seconds to rapidly change the time.
Release the button when you reach the desired time. Press "CLOCK" to confirm the time. The
icon will stop flashing.
N.B.:
• The time displays in the 24-hour clock format.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo Wall Dual 12000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo Wall Dual 12000 in the language / languages: English as an attachment in your email.

The manual is 2,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo Wall Dual 12000

Argo Wall Dual 12000 User Manual - German - 34 pages

Argo Wall Dual 12000 User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info