665482
28
Zoom out
Zoom in
Previous page
1/30
Next page
EG
28
Temperature delta setting for restart of the heat pump
When the water temperature reaches the set value or the maximum achievable value (in the case of Emix operation with-
out other indoor units), the heat pump switches off and starts up again only when the water temperature drops below the
desired temperature of a certain value (delta).
You can change the startup delta of the heat pump by setting it to 5°C or 10°C.
To change the set value, from the conguration menu, quickly press BUTTON 9 until the BLUE and RED LEDs are ash-
ing.
Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.
3 consecutive beeps conrm the setting.
NOTE
By default the startup delta of the heat pump is set to 10°C.
Reset of the factory settings
To reset all the factory settings, from the conguration menu, quickly press BUTTON 9 until the BLUE, YELLOW and RED
LEDs are ashing.
Then wait a few seconds until all the 5 GREEN LEDs light up and press BUTTON 9 once more.
3 consecutive beeps conrm the reset of factory settings.
In addition to the already described modes in the section “EMIX CONFIGURATION”, Emix software can automatically
manage electrical back up heaters under certain conditions. This mean that these operation modes are not to be set and
that can not be deactivated. They are:
- Antifreeze mode
- Cold draft prevention mode
- Electrical water heater mode (in case heat pump is not active)
- Antilegionella cycle
Electrical back up heater management – Antifreeze mode
If water temperature inside the tank is lower than 5° C, all connected electrical elements are switched on until the water
temperature reaches 10° C.
Electrical back up heater management – Cold draft prevention mode
When one or more indoor units are in cold draft prevention mode and compressor is operating since 20’, one by one
electrical element are switched on every 20’; they will be switched off one by one when no indoor unit will be any more
in Cold draft prevention mode.
Electrical back up heater management – Electric water heater mode
If the outdoor unit is stopped for maintenance the end user could decide to use Emix as controller of the electrical heater
elements located inside the tank, exactly like any electrical water heater. In this case, if the water temperature is lower
than the desired temperature for more than 10’, all the connected electrical heaters will switch on up to the reaching of
the setpoint. End users can switch off Emix if they do not want to utilise this option.
Electrical back up heater management – Antilegionella cycle
During the Antilegionella cycle, one or more electrical heaters may be automatically switched on. See section “ANTILE-
GIONELLA CYCLE”.
OPERATION OF THE ELECTRICAL HEATER ELEMENTS
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo Emix at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo Emix in the language / languages: English, German, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo Emix

Argo Emix User Manual - English - 29 pages

Argo Emix User Manual - German - 29 pages

Argo Emix User Manual - French - 29 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info