805048
9
Zoom out
Zoom in
Previous page
1/23
Next page
32V 05/23
HOW TO USE THE APPLIANCE
This appliance can be used for Cooling, Heating, Dehumidication and Ventilation. Before using the appliance, leave
it in an upright position for at least two hours.
Plug the power cord into an appropriate power outlet (220-240~V). Insert the batteries into the remote controller,
observing the polarities. Select the desired operating mode from the remote controller.
The air conditioner is equipped with a protection system which causes the unit to activate in Cooling, Dehumidication
and Heating mode only after an interval of approximately 3 minutes from the selection. Even when passing from one
mode to another, the fan continues to operate, but the compressor stops to restart after 3 minutes. This start delay
protects the compressor from overload.
This appliance is equipped with an automatic defrosting system which intervenes when the unit is running hot and ice
forms on the coil. The compressor stops for 10 minutes, after which the appliance resumes normal operation.
THE DRAINAGE TUBE MUST BE CONNECTED to the appliance AT ALL TIMES: the only exception is when the
appliance is used in dehumidication mode only, in which case the appliance should be left to discharge directly
into the room for maximum efciency (see the “Dehumidication Mode” paragraph).
Periodically clean the easily removable air lters located on the side of the product to keep the air conditioning efcient.
1. COOLING MODE (COOL)
Press the MODE button to select Cooling. The LED on the control panel lights up.
The temperature adjustment range goes from 16 °C to 32 °C with 1 °C steps.
In this mode, every time the unit is switched off by pressing the POWER button the appliance stores the set
temperature and when it is switched on again it will keep the setting.
In cooling mode, the fan speed is high by default, and the temperature present in the room is shown on the
display. Then use the UP/DOWN buttons to select the desired temperature
In this mode it is possible to adjust the ventilation speed (Speed), set the Timer and activate the Sleep function.
For quieter operation, reduce speed to low.
2. HEATING MODE (HEAT)
Press the MODE button to select Heating. The LED on the control panel lights up.
The temperature adjustment range goes from 16 °C to 32 °C with 1 °C steps.
In this mode, every time the unit is switched off by pressing the POWER button the appliance stores the set
temperature and when it is switched on again it will keep the setting.
In heating mode, the fan speed is low by default, and the temperature present in the room is shown on the
display. Then use the UP/DOWN buttons to select the desired temperature
In this mode it is possible to adjust the ventilation speed (Speed), set the Timer and activate the Sleep function.
For quieter operation, reduce speed to low.
3. DEHUMIDIFICATION MODE (DRY)
Press the MODE button to select the Dehumidication mode. The LED on the control panel lights up.
The temperature is controlled by the electronic board and cannot be adjusted.
Cooling, Heating, Fan Dehumidifying
OPERATING MODES
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo Einar Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo Einar Plus in the language / languages: English as an attachment in your email.

The manual is 5.43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo Einar Plus

Argo Einar Plus User Manual - German - 23 pages

Argo Einar Plus User Manual - Italian - 23 pages

Argo Einar Plus User Manual - Spanish - 23 pages

Argo Einar Plus User Manual - Spanish - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info