724569

Argo ECOLIGHT MULTI SPLIT Manual

10
Zoom out
Zoom in
Previous page
1/43
Next page
V 10/19
52
nessuna visualizzazione (il deflettore orizzontale si arresta nella
posizione corrente)
no display (the horizontal flap stops in the current position)
6. SLEEP button
In cool, heat or dry mode, press this button to start the SLEEP function. The icon will appear
on the remote control display. Press the button again to exit the SLEEP function. The icon will
disappear from the display.
The temperature will increase or decrease by 2 degrees over two hours according to the function
selected (cool/heat).
7. TEMP button
Pressing this button will allow you to display the set temperature, the indoor ambient temperature,
or the outdoor ambient temperature on the indoor unit's display. You can cycle through the settings
on the remote control display as shown below:
Nessuna visualizzazione
no display
• When you select or “no display” with the remote control, the set temperature will appear on
the indoor unit's display.
• When you select with the remote control, the indoor ambient temperature will appear on the
indoor unit's display.
• When you select with the remote control, the outdoor ambient temperature will appear on
the indoor unit's display.
N.B.:
• It is not possible to display the outdoor ambient temperature on all models. The indoor unit will
receive the signal but will display the set temperature.
• The set temperature will appear on the unit's display on start-up, if enabled to do so.
• When you select to display the indoor or outdoor ambient temperature, the indoor unit will
display the corresponding temperature for three to five seconds, after which it will automatically
revert to displaying the set temperature.
8. TURBO button
In cool/heat mode, press this button to switch to rapid cool/heat mode. The icon will appear on
the remote-control display. Press this button again to exit the TURBO function. The icon will
disappear from the display.
9. I FEEL button
Press this button to start the I FEEL function. The icon will appear on the remote control display.
When you select this function, the remote control will send the detected ambient temperature to
the indoor unit, which will then adjust its operation automatically based on the difference between
the detected temperature and the set temperature.
Press the button again to exit the I FEEL function. The icon will disappear from the display.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo ECOLIGHT MULTI SPLIT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo ECOLIGHT MULTI SPLIT in the language / languages: English as an attachment in your email.

The manual is 4,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info