724567
8
Zoom out
Zoom in
Previous page
1/22
Next page
8
ADJUSTING THE AIR FLOW DIRECTION
Make sure that the remote control unit has been turned on.
Press the button (FLAP) to select the sweep function.
CAUTION
Do not move the flap with your hands when the air
conditioner is running.
Sweep function
The flap starts moving up and down to deliver air
over the sweep range.
2. WHEN THE AIR CONDITIONER IS RUNNING
If you want to turn off the air conditioner push the ON/
OFF BUTTON (with the tip of a pen).
If you have lost the remote control unit or it has troubles,
follow the steps below.
1. WHEN THE AIR CONDITIONER IS STOPPED
If you want to turn on the air conditioner push the ON/OFF
BUTTON (with the tip of a pen).
OPERATION WITHOUT THE REMOTE
CONTROL UNIT
The air conditioner will enter the automatic mode
operation: it automatically selects the operating state
according to the indoor temperature (cooling, heating,
air supply), and cannot change the temperature setting
value and fan speed.
NOTE
NOTE
A) HOW TO SET THE ON TIMER
1. In the standby state, press the
TIMER button once to enter the
timed power-on setting state:
the symbol is blinking.
2. Press the + button (or - button) to
adjust the set time value (range 0.5-
24 hours), each time you press the
+ button (or -Key), the time value
increases (or decreases) by 0.5
hours.
After adjusting the time value, press
the timer button again to confirm and
enter the timed state:
the symbol lights. You can see
on the display the remaining time of
the power on.
B) HOW TO SET THE OFF TIMER
1. In the power-on state, press the
timer button once to enter the timer
shutdown setting state:
the symbol is blinking.
2. Press the + key (or - key) to adjust the
set time value (range 0.5-24 hours).
Each time you press the + key (or
- key), the time value increases (or
decreases) by 0.5 hours.
After adjusting the time value, press
the timer button again to confirm and
enter the timed shutdown state:
the symbol lights. You can see
on the display the remaining time of
shutdown.
SETTING THE TIMER
EN
BLOW
HUMIDITY
TIMER
LIGHT
ON/OFF
button
Power failure during operation.
In the event of power failure, the unit will stop. When the
power is resumed, the unit will restart automatically after
3 minutes.
NOTES
The flap automatically closes when the unit is off.
During the heating operation, the fan speed will be very
low and the flap will be in the horizontal position until the
air being blown out of the unit begins to warm. Once the
air warms up, the flap position and fan speed change to
the settings specified with the remote control.
Use the FLAP button on the remote control to adjust
the position of the flap. If you move the flap by hand,
the factual flap position and the flap position on the
remote control may no longer match. If this should
happen, shut off the unit, wait for the flap to close,
and then turn on the unit again; the flap position will
now be normal again.
CAUTION
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Argo Apollo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Argo Apollo in the language / languages: English as an attachment in your email.

The manual is 3,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Argo Apollo

Argo Apollo User Manual - German - 22 pages

Argo Apollo User Manual - French - 22 pages

Argo Apollo User Manual - Italian - 22 pages

Argo Apollo User Manual - Portuguese - 22 pages

Argo Apollo User Manual - Spanish - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info