578740

Arcam SoloSub Manual

6
Zoom out
Zoom in
Previous page
1/60
Next page
E-7E-6
English
Wireless connection
To pair the unit with a Solo bar make sure
the unit is turned on at the power switch.
1. Press the button on the remote
control unit of the Solo bar followed
by until Speaker/EQ Setup appears
on the front display panel. Press
followed by again, until Sub Pairing
appears.
2. Press to start the pairing procedure.
e display will change to In Progress.
3. Position the INPUT selector on the rear
of the Solo sub to WIRELESS.
INPUT
LINE
WIRELESS
LFE
Solo sub and Solo bar positioning
35
50
70
85
100
115
125
140
160
X-OVER FREQ
0.3
0.5
0.7
0.9
1.1
1.3
1.5
X-OVER Q VOLUME
0
1
2
3
4
5
6
7
8
9
10
PHASE
0˚ 180˚
Solo sub recommended settings
For Phase settings, please refer to the
information on page9.
Wired connections
We recommend the use of high-quality
screened audio cables. Poor quality cables
will degrade the performance of your
system. All cables should be kept as short as
is practically possible.
It is good practice when connecting your
equipment to make sure that the mains
power-supply cabling is kept as far away as
possible from your audio cables. Failure to
do so may result in unwanted noise in the
audio signals.
Note: When connecting the Solo sub to
audio cables, or when moving it to a new
position, make sure that the unit is switched
off and disconnect the power lead. Failure to
do so may result in damage to both speaker
and amplifier.
Subwoofer/satellite system
is is a multi-speaker system comprising
of two or smaller satellite speakers (or a
soundbar) coupled with a subwoofer. e
satellite speakers are dened as ‘small’
and are responsible for reproducing
higher frequency audio signals; while the
subwoofer reproduces the lower frequencies
where the smaller speakers are not capable.
If your sound source has an output marked
SUB, SUBWOOFER or LFE, connect it to
the white L/LFE input on the back panel
of the Solo sub using an RCA connector at
each end.
L/LFE
SUB
Make sure the INPUT selector is set to LFE.
e LFE input bypasses the crossover in the
Solo sub, so the crossover frequency should
be set by the surround sound amplier. For
the crossover setting, please see the response
of your speakers which may vary from
around 70Hz for large satellites, to 150Hz
for small speakers. We recommend 85Hz as
a starting point if you are unsure.
INPUT
LINE
WIRELESS
LFE
Stereo system with no LFE
is is a typical two-channel system (such
as an Arcam stereo amplier). If your sound
source does not have SUB or LFE outputs,
connect the right and le channels of the
stereo pre-amp outputs (PRE OUT L and
PRE OUT R) to the red R and white L/LFE
inputs respectively.
L/LFE
PRE-OUT L
PRE-OUT R
R
Make sure the INPUT selector is set to LINE.
e crossover frequency on the Solo sub
should be adjusted to the low frequency roll
o of the main speakers (see the manual
for your speakers for this information). e
Q-control (XOVER Q) can be used to ne-
tune the integration of Solo sub and your
main speakers (see page8 for information).
INPUT
LINE
WIRELESS
LFE
4. Press and hold the WIRELESS button
on the rear of the Solo sub for about ve
seconds. e WIRELESS LED will start
ashing blue, signalling that the Solo sub
is in sync mode and searching for a
WIRELESS
PAIRING
PWR WIRELESS
5. If the the pairing procedure was
successful, the WIRELESS LED will glow a
constant blue and the Solo bar will display
Linked.
6. Once the pairing procedure is nished,
the Solo sub will always reconnect
whenever it is powered on or receives an
audio signal.
Note: Sync mode lasts for about 30seconds.
If no source is detected during this time, the
Solo bar will stop searching and the process
will need to be repeated.
After connecting
Turn the volume down to minimum on the
sound source amplier before switching it
on. Switch the source amplier on, select a
source signal, then gradually increase the
volume to the required listening level.
Note: The wired connection will not work if
the Solo sub has been previously linked to a
Solo sub using wireless connection. To disable
the wireless connection, place the Solo bar to
its factory default settings. Refer to the Solo
bar user manual for how to do this.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam SoloSub at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam SoloSub in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 6,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info