160350
11
Zoom out
Zoom in
Previous page
1/30
Next page
E-11
movie 2.1
solo
English
listening in a second room
Solo Movie 2.1 provides two independent volume controls, offering you the possibility of
listening to the same output in two different rooms. To do this, you need the following:
< a power amplifier (such as the Arcam P90) and speakers
< suitable interconnect cables
< a remote control receiver (optional), available from your Arcam dealer
< a second remote control (optional), available from your Arcam dealer.
Make the connections as follows:
1. Ensure that all equipment is switched off and disconnected from the mains supply.
2. Connect the
ZONE 2/REC OUT outputs of Solo Movie 2.1 to the audio inputs of the
power amplifier using interconnect cables.
3. Connect the speakers to the speaker terminals of the power amplifier.
4. Plug the remote receiver from the second room into the connector labelled
REMOTE IN ZONE 2 on the rear of Solo Movie 2.1.
5. Reconnect the equipment to the mains supply and switch on. You should be able to
hear the output of Solo Movie 2.1 through the remote power amplifier, and control
the volume using the remote control.
Zone 2 volume control
Note that the second room is always muted when Solo Movie
2.1 is switched on – it must be unmuted ‘explicitly’ when
required. This is to avoid unexpected output in the
remote location.
The Zone 2 volume can be controlled from the main
room by using the front panel controls or the remote
control.
Front panel control:
1. Press and hold the
INFO button to turn the
‘Zone 2 Volume’ display on.
2. Unmute or change the previous volume setting
by pressing the VOLUME+ or –VOLUME buttons.
Remote control:
1. Press the
DVD button to ensure that the CR100
is in DVD mode.
2. Press SHIFT +
4
to turn the ‘Zone 2 Volume’ display on.
3. Unmute or change the previous volume setting by pressing
the + or buttons.
The ‘Zone 2 Volume’ display defaults to the previous display after about five
seconds.
viewing in a second room
If your set up is suitable for simultaneous video output (see ‘Using two video connections
simultaneously’, page 8), you can use the Composite video output for Zone 2.
Remember that Solo Movie 2.1 does not carry out video conversion, so for Composite
video to be available for Zone 2, it must be input as Composite video. If you have a
SCART-equipped unit, Composite video is included in the SCART connection. If you have
a Component (YUV) video unit, you will need to connect the Composite signal using a
phono–phono (RCA) cable rated at 75
Ω.
Controlling Solo Movie 2.1 from a second room
The Solo Movie 2.1 will require a remote pick-up device with a 12V external
power supply (such as a Xantech Dinky Link – see www.xantech.com) located
in Zone 2, together with a power amplifier (such as an Arcam P80 or P90) to
complete the system.
The diagram below shows the wiring scheme, which will also apply to other IR
pick-up devices commonly available.
Solo Movie 2.1 can also provide a +12V trigger output to control devices such as
the power amplifier in Zone 2. The +12V trigger is active when the unit is On or in
Clock mode.
+12V
0V
+12V
0V
Signal
Tip = Signal
12V TRIGGER input
Dinky Link, located in Zone 2
Sleeve = 0V
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam solo movie 2 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam solo movie 2 1 in the language / languages: English as an attachment in your email.

The manual is 1,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Arcam solo movie 2 1

Arcam solo movie 2 1 User Manual - German - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info