578808
7
Zoom out
Zoom in
Previous page
1/50
Next page
E-7
English
Single wiring
If each speaker has more than one pair of connecting terminals, use the terminals labelled
LF or ‘Low Frequency’ for each speaker.
Connect the positive terminal of the right speaker connection on the amplier (coloured
red and labelled
+R) to the positive terminal of your right speaker. Similarly, connect the
negative terminal of the amplier (coloured black and labelled with R) to the negative
terminal of your speaker. Repeat the process for the le speaker, using the amplier
terminals labelled +L and L.
If your speakers support bi-wiring, then there is a strip of conductive metal on the
speakers connecting the low-frequency terminals to those for the higher-frequencies; this
MUST NOT BE REMOVED in a single-wired system.
Bi-wiring
Bi-wiring is performed in the same way as single wiring except that, for each speaker, a
pair of cables are used to connect the amplier to each speaker.
Follow the instructions given for single wiring; then perform the same actions, this time
connecting the upper set of speaker terminals on your amplier to the terminals labelled
HF or ‘High Frequency’ for each speaker. Please refer to the illustration.
Speakers that support bi-wiring have a strip of metal on the speakers connecting the low-
frequency terminals to those for the higher-frequencies; this MUST BE REMOVED in a
bi-wired system.
Bi-amping
Bi-amping requires the use of two amplier channels per speaker. Using this method will
prevent you from using seven surround speakers.
Connect two channels of the P777 with a phono cable between the
AUDIO OUT socket on
one channel to the AUDIO IN channel of another. One channel should then be connected to
the speakers as described for single wiring, with the exception that this channel should be
connected to the speaker terminals labelled HF or ‘High Frequency’. e second channel must
then be connected to the LF or ‘Low Frequency’ terminals, as in the diagram.
Note that the strip of metal on the speakers connecting the lower terminals to the upper
terminals MUST BE REMOVED. Failure to do so will result in damage to both ampliers,
which will not normally be covered under warranty.
Arcam recommends that the phono connections are use for bi-amping. If you prefer to use the
XLR connectors, use a Y-lead with one female XLR to two male XLRs, so that two amplier
channels may be fed from a single source. Contact your dealer if you need assistance.
Bi-wiring using one amplier
channel per speaker
Bi-amping using two amplier
channels per speaker
Single wiring speaker
connections
Outputs from multichannel pre-amp (e.g AV888)
+
+
Ð
Ð
Arcam P777
+Ð
IN OUT
LF
HF
+Ð
IN OUT
+
+
Ð
Ð
Arcam P777
+Ð
IN OUT
LF
HF
+
Ð
+
Ð
+
Ð
LF
HF
LF
HF
+
+
Ð
Ð
+
Ð
Arcam P777
SBR SR R C L SL SBL
LF
HF
+
+
Ð
Ð
LF
HF
+Ð
IN OUT
+Ð
IN OUT
+Ð
IN OUT
+Ð
IN OUT
+Ð
IN OUT
+Ð
IN OUT
+Ð
IN OUT
...etc...
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam P777 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam P777 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info