578788
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
CONNECTING TO A POWER SUPPLY
WRONG PLUG?
Check that the plug supplied with the unit fits your supply and that
your mains supply voltage agrees with the voltage setting (115V or
230V) indicated on the rear panel of the unit
2
before plugging in.
If your mains supply voltage or mains plug is different, consult your
Arcam dealer or Arcam Customer Support on +44 (0)1223 203203.
The product must be earthed.
MAINS LEAD
The appliance is normally supplied with a moulded mains plug already
fitted to the lead. If for any reason the plug needs to be removed, it
must be disposed of immediately and securely, as it is a potential shock
hazard when inserted into the mains socket. Should you require a new
mains lead, contact your Arcam dealer.
PLUGGING IN
Push the plug (IEC line socket) of the power cable supplied with the
unit into the socket (
POWER INLET)
1
in the back of the unit. Make
sure it is pushed in firmly.
Put the plug on the other end of the cable into your power supply
socket and switch the socket on.
STANDBY POWER
For remote standby operation, the amplifiers control power supply
is kept powered up all the time the unit is connected to the mains
supply. The front panel power switch powers down all other circuitry.
Power consumption in this mode is less than 2W.
This means that even though the power switch is off, it may be possible
to hear a slight residual hum coming from the mains transformer inside
the amplifier. This is perfectly normal. If the unit is to be left unused for
an extended period, we recommend that it is disconnected from the
mains supply by switching it off at the wall socket.
CONNECTING TO OTHER EQUIPMENT
The use of high quality interconnect cables to and from your amplifier
is recommended to ensure the best sound quality. Sockets marked L
(and
R) on your amplifier should only be connected to sockets marked
L (and R) on other equipment. All the line inputs have the same
sensitivity and may be used with equipment other than that labelled,
if needed.
TAPE1/RECORD OUT
8
Connect these output sockets to
the input sockets of your cassette deck (usually labelled
RECORD).
TAPE1/PLAY IN
9
Connect these input sockets to the output
sockets of your cassette deck (usually labelled PLAY). If you do not have
a cassette deck you can use this input for other (line level) equipment,
such as a CD player, tuner, VCR, etc., but not a turntable.
VCR/TAPE2 RECORD OUT
bk
These output sockets can
be connected to the input sockets of VCR/second recorder (usually
labelled RECORD).
VCR/TAPE2 PLAY IN
bl
Connect these input sockets to the
output sockets of your VCR/second recorder (usually labelled
PLAY).
Alternatively, you can use this input for other (line level) equipment
such as a CD player, tuner, etc., but not a turntable.
DVD
bm
Connect this input to the audio outputs of a DVD
player.
AV
bn
Connect this input to audiovisual equipment such as a VCR,
laserdisc player, satellite or Nicam tuner.
TUNER
bo
Connect this input to the audio outputs of your radio
tuner.
CD
bp
Connect this input to the audio outputs of your CD player
or DAC (digital to analogue converter).
AUX
bq
Connect this input to the audio outputs of any unit with
a line level output, e.g. tape deck, tuner etc.
PHONO
bq
Connect this input to the audio outputs of your
turntable. This Phono Module is compatible with most high output
moving coil and moving magnet cartridges (MM) and low output
moving coil cartridges (MC). MM or MC can be selected via the blue
switch on the rear panel.
Phono earth terminal For connecting your turntable earth lead
(if fitted). Note that this terminal must not be used as a safety earth.
TRIG OUT and REMOTE IN
3
(12V in and out) These
connections are for use in multi-room installations. In normal use there
is no need to make any connections to these sockets. If you are
bi-amping with a power amplifier and wish to power both units on or
off simultaneously, see page 11.
PRE/POWER AMPLIFIER CONNECTIONS
PWR IN
5
To use your integrated amplifier as a power amplifier,
connect the output of your pre-amplifier to the PWR IN sockets.
Press in the PRE/PWR switch
7
on the rear panel to select separate
pre-amp/power amp mode. Under these circumstances your A32 has
exactly the same specification and performance as a power amplifier
(see page 8).
PRE OUT
6
To use your integrated amplifier as a pre-amplifier,
connect the PRE OUT sockets to the input sockets of your power
amplifier. With a power amplifier of the correct gain (e.g. the P35
power amplifier) you can bi-amplify (bi-amp) suitable loudspeakers,
giving significant improvements in sound quality (see page 13).
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam FMJ A32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam FMJ A32 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info