578788
5
Zoom out
Zoom in
Previous page
1/16
Next page
5
POSITIONING THE UNIT
Place your amplifier on a level, firm surface.
Avoid placing the unit in direct sunlight or near sources of heat or
damp.
Ensure adequate ventilation. Do not place the unit in an enclosed
space such as a bookcase or cabinet as both of these will impede air
flow through the ventilation slots.
CONNECTING TO LOUDSPEAKERS
You can connect one or two pairs of loudspeakers to your amplifier,
provided each pair is rated between 816. If one or both pairs have
an impedance of less than 8, the combined load on the amplifier falls
below 4 and could cause an overload. If so, the overload protection
circuit engages and the amplifier will not work.
To connect one pair of loudspeakers, use the
SP1 terminals.
SP1 and SP2 terminals
4
Both sets of loudspeaker terminals can be switched off by pressing the
MUTE button on the remote control. To switch SP1 and SP2 independently,
use the front panel switch
7
(see page 7) or the remote control (see
page 10).
Your amplifier is fitted with loudspeaker terminals to BFA (British
Federation of Audio) standard specification.
BFA loudspeaker terminals
The terminal will accept spade terminals, bare wires or a BFA plug.
BFA plugs are available from your Arcam dealer. To connect a bare wire
or spade terminal, unscrew the red (or black) part of the loudspeaker
terminal first.
Insert the wire or spade terminal and screw it back up.
Installation: A32 integrated ampli er
Wiring your loudspeakers
LR
+–
PHONO
+–
SP1
SP2
POWER INLET
PRE OUTPWR IN
6 8 9 bk bl bm bn bo bp54 bq1
4 – 16 OHMS
L
R
L
R
L
R
VOLTAGE
SELECT
RECORD
OUT
PLAY
IN
TAPE/PROC
RECORD
OUT
PLAY
IN
VCR/TAPE 2 DVD AV TUNER CD AUX
INTEGRATED
PRE/PWR
MM
MC
32
REMOTE
IN
TRIG
OUT
7br
115/230V
Arcam A32 amplifier
R
L
+ +
Right
speaker
+
+
Left
speaker
CAUTION: Do not over tighten the loudspeaker terminals or use
a wrench, pliers, etc., as this could cause damage to the terminals
which will not be covered under warranty.
Connect the right speaker to the terminals on the back of your
amplifier marked
R and the left speaker to the terminals marked L.
Connect your loudspeakers so that the red (positive/+) terminal on
each loudspeaker is connected to the red (positive/+) terminal on the
amplifier. Your loudspeaker cables may be marked to show polarity
(negative/ and positive/+), if not, then the positive terminal can usually
be identified by a ridge or coloured marking.
Now connect your loudspeakers black (negative/) terminals to the
black (negative/) terminals on the amplifier.
Ensure that no stray strands of inner wires are allowed to touch
another cable or the amplifiers casing. This can cause a short circuit
and damage your amplifier!
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam FMJ A32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam FMJ A32 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info