578767

Arcam DiVA AVR200 Manual

14
Zoom out
Zoom in
Previous page
1/19
Next page
AVR200
14
RDS INFO
FM MUTE/
MONO STORE
PRESET/
TUNE DOWN/UP
MHz
VIDEO 1
DOLBY PL II SPEAKERS
TUNED FM STEREO PRESET
MUSIC
FM MUTE
Using the tuner
The AVR200’s radio tuner can be controlled from the upper row
of front panel buttons (see diagram, below) or from the remote
control handset (see ‘Using the remote control’).
Tuning to a station
Pressing the PRESET/TUNE button toggles between the two
tuning modes of the unit – ‘Preset’ or ‘Tune’. The selected mode
is briefl y shown in the display.
Preset mode
In Preset mode, press the
•
and
•
buttons on the front panel
(or P– or P+ on the remote control handset) to cycle up and
down the preset stations.
See ‘Storing a preset’ and ‘Deleting unused presets’, below.
Tune mode
In Tune mode:
■ Press the
•
and
•
buttons on the front panel (or P– or
P+ on the remote control handset) for longer than half-a-
second to engage automatic tuning. The tuner searches
for a radio station signal of suffi cient strength and stops.
To skip to the next station, press one of the buttons
again. Automatic tuning is available for both the FM and
AM bands.
■ Tapping the
•
and
•
buttons engages manual tuning. This
can be used for tuning to a specifi c frequency. It is also
useful if you are trying to select a station that is too weak
for the auto search mode.
Regardless of the mode used to tune your AVR200, when it
is accurately tuned to a station ‘
•
TUNED
•
’ lights up in the
display.
Storing a preset
To store a preset, tune to the radio station you wish to store.
Press the STORE button: this causes ‘MEMORY’ to fl ash in the
display. Now select the preset number you wish to assign to
the station using the
•
and
•
buttons on the front panel (or
P– or P+ on the remote control handset). Press the STORE
button again.
Once the preset is stored, the display reverts to show the
station name (if RDS information is transmitted) or its frequency.
To quit the memory function without storing a preset, leave the
tuner controls untouched for ten seconds. It is also possible to
overwrite a stored station by saving another in its place. There
are thirty presets available for FM use and ten for AM use.
Your presets are retained for several weeks (but not indefi nitely),
when the AVR200 is disconnected from the mains supply.
Deleting an unused preset
Press the STORE button, then select the preset number you
want to delete using the
•
and
•
buttons (or P– or P+ on
the remote control handset), followed by the FM MUTE/MONO
button.
The display briefl y shows ‘DELETED’ and ‘– –’ is shown in
place of the preset number. You can reactivate a deleted preset
number by storing a station in the normal way.
Radio interference
All Arcam products have been designed to very high
standards of electromagnetic compatibility.
However, both CD players and DACs generate, and can
radiate RF (radio frequency) energy. In some cases this can
cause interference with FM and AM radio reception. If this is
the case, switch the CD player off or keep the CD player and
its connecting cables as far from the tuner and its aerials as
possible. Connecting the CD player and the tuner/amplifi er to
different mains sockets can also help to reduce interference.
EC COUNTRIES -– These products have been designed to
comply with directive 89/336/EEC.
USA – These products comply with FCC requirements.
RDS: Radio Data System
The Arcam AVR200 supports RDS Programme Service and RDS
Radio Text on FM broadcasts.
When a station carrying RDS information is selected ‘RDS’ lights
up in the display and shortly afterwards the station’s RDS name
(e.g. ‘BBC R3’) is shown.
Press the
RDS INFO button to view any RDS text information (if
a station is not transmitting text information, the display briefl y
indicates ‘NO TEXT’ and reverts to show the station name).
Press
RDS INFO again to display the station’s frequency.
Pressing
RDS INFO a third time returns you to a display of the
station name.
If the
RDS INFO button is pressed while tuned to a non RDS
station, the display shows ‘NO NAME’ for three seconds before
reverting to the default display.
FM Mute/Mono
The AVR200’s tuner has an auto-muting circuit that, when
engaged, mutes any signal that is of insuffi cient strength for
listening. To engage this circuit press the FM MUTE/MONO
button on the front panel: ‘FM MUTE’ is shown in the display.
If a signal is muted you will hear no sound through the
loudspeakers.
Should you wish to listen to a station that is ‘auto muted’
press the
FM MUTE/MONO button again to disengage the
muting circuit. The tuner now switches to monoaural reception,
cancelling much of the background hiss. ‘FM MUTE’ is no longer
displayed and you are able to continue listening.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam DiVA AVR200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam DiVA AVR200 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info