578767
16
Zoom out
Zoom in
Previous page
1/19
Next page
AVR200
16
Before you start
WARNING: Do not make any connections to your
ampli er while it is switched on or connected to the
mains supply.
Before switching on please check all connections
thoroughly, making sure bare wires or cables are
not touching the ampli er in the wrong places (which
could cause short circuits) and you have connected
positive (+) to positive and negative () to negative.
Always ensure that the volume control on your
ampli er is set to minimum before starting these
procedures.
Bi-wiring your loudspeakers
Bi-wiring improves the sound of your system because it divides
the high and low frequency signal currents into separate
speaker cables. This avoids signal distortions arising from the
high and low frequency currents interacting with one another
within a single cable, as in conventionally wired systems.
You will need:
Speakers with four input terminals each: these will be marked
HF (High Frequency) and LF (Low Frequency).
Loudspeaker cables two pairs of cables per loudspeaker
(which may be joined at the ampli er end if your ampli er has
only one pair of output terminals per channel). Or, a suitably
terminated cable set (a loom, probably prepared by your dealer
and capable of being used for bi-wiring in one length).
How to bi-wire loudspeakers
1. Remove the terminal links on the rear of your
loudspeakers
WARNING: This step is essential or damage to
your ampli er may result which is not covered
under warranty.
2. Connect the cables as shown in the diagram below,
ensuring correct polarity at all times.
Bi-amping your system
The performance of your system can be further enhanced over
that achieved with bi-wiring, by extending the principle one stage
further to include separate ampli cation for the low and high
frequency drive units in each loudspeaker enclosure.
Connect the AVR200 to the high frequency (HF) terminals
and connect your power ampli er to the low frequency (LF)
terminals.
You will need:
Speakers with four input terminals each (as with bi-wiring):
these will be marked HF (High Frequency) and LF (Low
Frequency).
Two ampli ers one of these would be the AVR200 and the
other an Arcam power ampli er (e.g. an P75 or P85).
Loudspeaker cables one pair of cables per loudspeaker or
a suitably terminated cable set (a loom, probably prepared by
your dealer and capable of being used for bi-amping in one
length).
Interconnect cables one pair of high quality interconnect
cables.
How to set up a bi-amped system
1. Remove the terminal links on the rear of your
loudspeakers.
WARNING: This step is essential or damage to
your ampli er may result which is not covered
under warranty.
2. Connect the cables as shown in the diagram below,
ensuring correct polarity at all times.
3. Use the interconnect cables to connect the AUDIO PRE-
OUT sockets of the AVR200 to the corresponding PWR
AMP IN sockets of the power ampli er.
Reference
Bi-wiring and bi-amping loudspeakers
R
L
Right
speaker
Left
speaker
Arcam AVR200 receiver
HF
LF
+
+
+
HF
LF
+
+
+
RL
Arcam AP85 power amplifier
+ +
R
L
Arcam AVR200 receiver
+
+
Right
speaker
HF
LF
+
+
HF
LF
+
+
Left
speaker
Bi-wiring using one set of connections on ampli er Recommended bi-amping con guration
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Arcam DiVA AVR200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Arcam DiVA AVR200 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info