Manual Arcam AVR400 (page 27 of 236) (English, German, Dutch, French)

578747

Zoom out

Zoom in

1/236

E-25

English

Controlling other devices

Method 1 (Direct code setup)

is section describes the simplest (preferred) way to

program the CR102’s Device Mode keys to control the

non-Arcam devices in your system.

DVD

SAT AV

TUN

AMP

PVR VCR

Some of the modes are locked to Arcam operation but

can be unlocked if required (see page E-50).

mode only controls Arcam equipment.

BD mode Locked

SAT mode Unlocked

AV mode Unlocked

TUN mode Locked

PVR mode Locked

VCR mode Unlocked

CD mode Locked

Here is a specic example of how to program the

key to control an Addison television. e principles for

controlling other devices are exactly the same.

1. Make sure your device is switched on (not just on

standby).

2. Find the correct Device Code table (e.g. TV) for the

type of device you want to control from the CR102.

3. Find the row containing the codes for the

manufacturer of your device (e.g. Addison) (page 56).

e most popular code is listed rst.

4. Press the appropriate Device Mode key (e.g.

) on

the CR102.

5. Press and hold

until the red Power LED blinks

twice:

* *

(It actually blinks once when you press

the key, then twice aer about three seconds).

6. Enter the rst four-digit device code using the

number keys. e power key blinks twice:

* *

7. Aim the CR102 at the device and press

. If the

device switches o, the setup is complete.

8. Turn your device back on and test all the CR102’s

functions to ensure they are working properly.

9. Important! Write your device code down on the

right hand side of the page so you can remember it if

you ever reset the CR102.

What if I still can’t control my device?

If your device doesn’t respond, repeat the above

steps until one of the device codes listed for your

brand works.

If none of the codes listed for your brand operates

your device, or if your brand is not listed at all, try

the Library Search Method described in the next

section.

Notes:

Some codes are quite similar. If your device does not

respond or is not functioning properly with one of

the codes, try another code listed under your brand.

If your device’s original remote control does not have

(POWER) key, press

instead of

when

setting up your device.

Remember to press the corresponding device key

before operating your device.

Many TVs do not switch on pressing

. Please try

pressing a number key (‘channel select’) to switch

your TV back on.

To search for the code for another device follow the

instructions above, but press the appropriate device

key instead of

during step 2.

Method 2 (Library search)

is section describes another way to program the

CR102 to control third-party equipment.

Library Search allows you to scan through all the

codes contained in the CR102’s memory. It can take a

lot longer than the previous method, so only use this

method if:

Your device does not respond to the CR102 aer you

have tried all the codes listed for your brand.

Your brand is not listed at all in the Device Code

tables.

Example: To search for a TV code

1. Switch your TV on (not standby) and aim the

CR102 at it.

2. Press

on your CR102.

3. Press and hold

until the power LED blinks twice.

4. Press

. e power LED key blinks twice:

5. Press

6. Aim the CR102 at your Television and press

[

repeatedly until your Television turns o.

Every time you press

[

the CR102 sends out a

POWER signal from the next code contained in its

memory. In the worst case, you may have to press this

key up to 150 times, so patience is required! If you

skip past a code, step back by pressing

]

. Remember

to keep pointing the CR102 at your Television while

pressing this key.

7. As soon as your television turns o, press

store the code.

Notes:

Many TVs do not switch on by pressing

. Try

pressing a number key (‘channel select’) to switch

your TV back on.

If you cannot control your Television properly,

please continue the Search Method: you may be

using the wrong code.

To search for the code for another device follow the

instructions above, but press the appropriate Device

Mode key instead of

during step 2.

If your device’s original remote control does not have

(STANDBY) key, press

instead during step 5.

Code blink-back

Once you have set up your CR102, you can blink back

your device set-up codes for future reference.

Example: To blink back your Television code

1. Press the appropriate Device Mode key (e.g.

)

once.

2. Press and hold

until the red Power LED blinks

twice

(It actually blinks once when you press

the key, then twice aer about three seconds).

3. Press

. e

key blinks twice.

4. For the rst digit of your four-digit code, press

and count all the red blinks. If there are no blinks,

the digit is ‘0’.

5. For the second, third and fourth digits, repeat the

previous step, pressing

, or

in order.

Now you have the four-digit code.

Make a note of the codes

Write down the codes for your devices in the boxes

below for future reference.

Device Code

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Arcam AVR400 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 16,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Arcam AVR400 Manual

Product: