780165
6
Zoom out
Zoom in
Previous page
1/24
Next page
6
ERASING TEMPORARY DATA
To erase the temporary data (trip, time, avg, max)
twice push the button M. rES will show on the
display. Pick option M with buttons A and C
and confirm with buttonM.
PARAMETERS SETTING
To enter the mode of parameter setting press
twice the M button. To change a parameter,
use buttons A andC and for saving the set
parameter press the M button.
TURNING ON THE LIGHTING
IF IT IS INSTALLED
Turning on the front and rear light is done by
pushing and holding the A button for 1 second.
USB PORT
The display is equipped with a micro USB port
for charging of mobile devices (5V/0,5W).
To connect your device with the charging
connector, use any adapter or cable with Micro
USBB connector.
WALKING ASSISTANT
Walking assistant can be activated by pressing
and holding the Cbutton on the control display.
For activation of the assistant assistance mode
must be set to 1-5. This function serves to enable
easier manipulation with e-bike, usually when
walking the bike by your side. The e-bike speed
will be between 4 and 6 km/h. Walking assistant
will be turned off immediately after letting go of
the button.
WARNING: Do not block the e-bike
Lafter the activation of the walking
assistant. The motor can get damaged
that way.
SPEED AND DISTANCE INDICATOR MODE
CHANGE
Change of information displayed on the display
can be done by short press of the button M.
Information shows in this order:
rES – reset of daily kilometres
Un – unit setting (km / mile)
Ld – setting of the bike circumference in cm (max. +/- 5 % from the default setting of the circumference)
bL – display backlight setting in 1-3 range
Ls – speed limit; value 20 means max. assisted speed of 25 km/h
SPS – wheel speed sensor signal
Cr – value of the electric current
TRIP
Lenght of the trip
ODO
Total distance
TIME
Time*
MAX
Maximum speed
AVG
Average speed
ERROR
MESSAGES Code Cause of the problem
0X0000 no error
0X0001 controller power tube or over current
0X0002 controller over heat
0X0004 motor phase
0X0008 motor hall
0X0010 motor over heat
0X020 low voltage protection
0X0040 stall protection
0X0080 throttle
0X0100 over-speed beyond control
0X0200 battery communiction
0X0400 pas sensor
0X0800 speed sensor
0X1000 display communication
If the error remains or a different one shows, contact your seller.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Apache E-Bikes 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Apache E-Bikes 2020 in the language / languages: English as an attachment in your email.

The manual is 1.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info