Manual Apache E-Bikes 2020 (page 5 of 24) (English)

780165

Zoom out

Zoom in

1/24

USER MANUAL

FOR EBIKES

Congratulations on purchasing the e-bike from

We wish you many effortless kilometres and

many unusual experiences.

We strongly believe that you will

be satisfied with your e-bike.

Any bike equipped with an electric motor,

electronic central unit and battery is considered

an e-bike. The drive unit ﬁlls the role of something

of a helper that helps the rider with pedalling and

cares for his comfort. At the same time the motor’s

help will activate only if the rider is pedalling and

actively turning the cranks. The crank movement

is read by a special sensor place in the bottom

bracket. Maximum speed of an e-bike with motor

assistance is ca. 25 km/h. After reaching this

speed the motor automatically turns itself o and

you continue as with any normal bike. If the battery

runs out or if the electric motor is turned o, you

can still continue to your goal using your own

strength without any further resistance.

Electric motor can be set in motion also via control

button or accelerator, but only up to maximum

allowed speed of 6 km/h. This function is usually

called walking assistant and it is useful for any

manipulation with e-bike. Reaching higher speeds

is impossible without active help from the rider.

Every e-bike that conforms to European norm

EN 15194-1 is, from the point of the Road Trac

Law, considered a normal bike. You don’t a driver’s

license for an e-bike like this, you can freely ride on

cycling trails and cycling helmet is mandatory only

up till 18 years of age. We still strongly recommend

the use of cycling helmets to all e-bike users

without distinction.

WHAT IS AN EBIKE AND WHAT IT CONSISTS OF

Battery 2

Wheel speed sensor Turn indicator

Control panel

Brake levers with

braking sensors 1

Electronic

Control Unit

motor 3

Technical data of an Apache e-bike:

Rated power of the motor 250 W

System voltage 36 V

Operational temperature 0 / +40 °C

Storage temperature -10 / +50 °C

Protection degree IP 54

(protection from dust, splashing water)

1 Only models with mechanical brakes.

2 Battery can be placed on the frame tube, behind the seatpost or in the carrier.

3 Motor can be placed in the rear wheel, front wheel or in the bottom bracket.

BASIC INFORMATION

FOR EBIKE USE

Check the functionality of brakes and state

of charge of the battery before every ride.

Always wear a cycling helmet when riding an e-bike!

IMPORTANT!

ADVICE

RIDING AN EBIKE

You can ride an e-bike the same way as a normal

bike. You just have to drive off and pedal. Motor

will activate itself after the cranks start turning

and works according to set assistance mode.

The motor turns itself off automatically if the

rider brakes. This is not true for models with

hydraulic disc brakes, as their levers are not

equipped with all necessary sensors.

Motor of these models turns off after two

seconds after you stop pedalling.

Once you reach the speed of 25 km/h, the motor

automatically turns itself off and activate again

when the speed goes under this limit.

Motor also doesn’t work when you’re not

pedalling or turning cranks backwards.

Long-term riding with low motor speed and high mode of assistance can lead to overheating

and, in case of excessive load, even to damage of the motor. If this happens, we strongly

recommend to reduce the mode of assistance.

EBike’s function can be influence by external electromagnetic forces (i.e. radars, etc.).

In case of troubles with changing gears to lighter or heavier gear we recommend additional

installation of “Gear sensor” that disables the motor for a short while during the gear change.

The gears then don’t change while the motor is using its full power, which is considerate not only

to the motor itself, but also to other components.

TURNING ON AND OFF

1. Turn on the power on the battery.

Activate the battery by pushing a button

on its body.

2. Turn on the LCD panel of the e-bike

Press the M button on the display

controller and hold for 5 seconds.

This will also turn off the electric system.

For turning off a frame battery, hold the

button for 4 seconds. The system will turn

itself off automatically after 10 minutes of

inactivity for energy-saving reasons.

SETTING OF THE ASSISTANCE MODE

To change the mode of assistance in range of

0-5 shortly press buttons Cand A . Highest

mode of assistance is marked with number 5,

lowest marked 0 is without electric motor’s

assistance.

During a ride with low engine speed

L and high assistance mode

the motor can start vibrating for a short time.

In such a case we recommend to immediately

decrease the level of assistance.

mph

km/h

TRIP ODO TIME MAX AVG RANGE ERROR

mi/h

km/h

speed units

walking assistent

speed / distance

units

power indicator

assistance mode

state of charge

lighting

speed indicator

speed

/ distance display

mode of speed

/ distance indicator error message

USB port

Tuwan E3, Tuwan E5, Yamka E3, Yamka E5, Tate, Matto Tour E3, Matto Tour E5, Matta

E7, Matta Tour E3, Matta Tour E5, Matta E7, Wakan Tour E3, Wakan Tour E5, Wakita

Tour E3, Wakita Tour E5, Wakan City, Wakita City, Tocho Plus, Tocho Plus+

CODAC 

EBIKE CONTROLS

frame battery

seatpost battery integrated battery

ERASING TEMPORARY DATA

To erase the temporary data (trip, time, avg, max)

twice push the button M. rES will show on the

display. Pick option M with buttons A and C

and confirm with buttonM.

PARAMETERS SETTING

To enter the mode of parameter setting press

twice the M button. To change a parameter,

use buttons A andC and for saving the set

parameter press the M button.

TURNING ON THE LIGHTING

IF IT IS INSTALLED

Turning on the front and rear light is done by

pushing and holding the A button for 1 second.

USB PORT

The display is equipped with a micro USB port

for charging of mobile devices (5V/0,5W).

To connect your device with the charging

connector, use any adapter or cable with Micro

USBB connector.

WALKING ASSISTANT

Walking assistant can be activated by pressing

and holding the Cbutton on the control display.

For activation of the assistant assistance mode

must be set to 1-5. This function serves to enable

easier manipulation with e-bike, usually when

walking the bike by your side. The e-bike speed

will be between 4 and 6 km/h. Walking assistant

will be turned off immediately after letting go of

the button.

WARNING: Do not block the e-bike

Lafter the activation of the walking

assistant. The motor can get damaged

that way.

SPEED AND DISTANCE INDICATOR MODE

CHANGE

Change of information displayed on the display

can be done by short press of the button M.

Information shows in this order:

rES – reset of daily kilometres

Un – unit setting (km / mile)

Ld – setting of the bike circumference in cm (max. +/- 5 % from the default setting of the circumference)

bL – display backlight setting in 1-3 range

Ls – speed limit; value 20 means max. assisted speed of 25 km/h

SPS – wheel speed sensor signal

Cr – value of the electric current

TRIP

Lenght of the trip

ODO

Total distance

TIME

Time*

MAX

Maximum speed

AVG

Average speed

ERROR

MESSAGES Code Cause of the problem

0X0000 no error

0X0001 controller power tube or over current

0X0002 controller over heat

0X0004 motor phase

0X0008 motor hall

0X0010 motor over heat

0X020 low voltage protection

0X0040 stall protection

0X0080 throttle

0X0100 over-speed beyond control

0X0200 battery communiction

0X0400 pas sensor

0X0800 speed sensor

0X1000 display communication

If the error remains or a different one shows, contact your seller.

ON/OFF

13:14 76%

48.2

km/h

TRIP 265.9Km

250

500

750

km/h

state of charge

Time

USB charging

Lighting

voltage / battery

percentage indicator

Speed

indicator mode

power indicator

data indicator

assist. mode

(Tuwan MX1, Tuwan MX3, Tuwan MX5, Yamka MX1, Yamka MX3, Yamka MX5, Matto MX1, Matto MX3, Matto MX5,

Matta MX1, Matta MX3, Matta MX5, Wakan MX3, Wakan MX5, Wakita MX3, Wakita MX5)

TURNING ON AND OFF

1. Turn on the power on the battery

Activate the battery by pressing a button

on its body.

2. Turn on the TFT panel

Press the Mbutton on the display controller

and hold it for 2 seconds. The system can be

turned off the same way. To turn off a frame

battery, hold the button for 4 seconds. The

system will turn itself off automatically after

5 minutes of inactivity (this time can be adjusted

– see Parameters setting further) for energy-

saving reasons.

SETTING OF THE ASSISTANCE MODE

To change the mode of assistance in range

of 0-5, shortly press the Aand C buttons.

Highest assistance mode is marked by number 5,

mode without the help of the motor is marked by

number 0. After turning on the display the mode

is automatically set to value of 1.

During a ride with low engine speed and

Lhigh assistance mode the motor can

start vibrating for a short time. In such a case we

recommend to immediately decrease the level of

assistance.

WALKING ASSISTANT

Walking assistant can be activated by pressing

the Cbutton, with which you set the assistance

to the mode of walking assistant (symbol of

walking assistant will appear). Then press the

button again and the assistant will be active until

you let go. This function serves to enable better

manipulation with e-bike, typically when walking

with bike by your side. The e-bikes speed will

be between 4-6 km/h. Walking assistant will

be turned off immediately after letting go of the

button.

WARNING: Do not block the e-bike

L after activation of the walking

assistant. The motor can get damaged that

way.

TFT COLOUR 

EBIKE CONTROL

If the error remains or a different one shows, contact your seller.

frame battery

seatpost battery integrated battery

SPEED AND DISTANCE INDICATOR MODE CHANGE

Change of information displayed on the display

can be done by short press of the button H.

DISPLAY BACKLIGHT CONTROL

To turn the display backlight on or off, hold

the A button for 2 seconds. During bad light

conditions, the backlight turns on automatically.

If it then turns off, it’s necessary to turn it on

manually. The intensity of the backlight can be

set – see Parameters setting further. Doing this

will also turn on and off the front/rear lights on

Tour models.

ERASING TEMPORARY DATA

To erase temporary data, proceed according

to article Parameters setting. You will get to

erasing of temporary data through “Display

setting” and “TRIP reset” (as soon as the line

TRIP reset is highlighted, press the Gbutton

and set the “YES” value via Aand C buttons.

Then confirm it by the button G and temporary

data will be erased). Temporary data will be

automatically erased after reaching 99:59 h of

total ride time. Temporary data won’t be erased

in case of turning the display off.

PARAMETERS SETTING

To enter the parameters setting mode press the

Gbutton twice with interval ca. 0,3 seconds.

To switch between different menu items and

the parameters setting change use buttons

AandC. To confirm your choice, press the

Gbutton. To end the parameters setting mode,

press the G button twice with interval ca. 0,3

seconds. In case of inactivity for 10 seconds the

parameters setting mode ends automatically.

ITEM DISPLAY SETTING

TRIP

Lenght

of the trip

ODO

Total

distance

MAX

Maximum

speed

AVG

Average

Speed

RANGE

Remaining

range

TIME

Total time

of the ride

Unit – unit setting (km/mile)

Brightness –display backlight intensity setting (10, 30,

50, 75 or 100 %)

Auto Off –setting of automatic display shutdown

(1–9 min)

Max Pas – setting of assistance number (3/5/9)

Power View – setting of power indicator format

(power/torque)

SOC View –setting of battery indicator format

(percentage/voltage)

TRIP reset – temporary data erasure (TRIP, MAX, AVG,

TIME)

AL Sensitivity –setting of light sensitivity (0 – 5, 0 =

switched-off sensitivity sensor)

Set Clock – time setting

Back – back

ITEM INFORMATION

Setting items can differ according to the version

of display software.

Battery info – general information about the status and

attributes of the battery

Error Code – general information of carried-out error

reports (max. 10 items)

Back – back

ERROR MESSAGES

Code Cause of the problem

07 Protection from battery overvoltage (check the battery voltage).

08 Error of hall sensor of the motor (check the setting and connection with motor).

09 Error of motor phase cable (check the setting and connection with motor).

11 Error of temperature sensor of the ECU (check the setting and connection with

ECU).

12 Torque sensor error (check the setting and connection with motor).

13 Excessive battery temperature (turn o the system and wait).

14 Excessive motor temperature (turn o the system and wait).

21 Speed sensor error (check the setting and connection with motor).

22 Error of BMS interface (change the battery).

25 Cadence sensor error (take out the battery and return it, if the error remains, visit a

repair shop).

30 Communication error (check all connectors’ connection).

If the error remains or a different one shows, contact your seller.

TURNING ON AND OFF

1. Turn on the power on the battery

Activate the battery by pressing a button on

its body.

2. Turn on the e-bike’s control panel

Press and hold the Mbutton on the

controller for 5 seconds. The system can be

turned off the same way. The system turns itself

off automatically after 10 minutes of inactivity

from energy-saving reasons.

SETTING OF THE ASSIST. MODE

You can change the mode of assistance in

range of 1-5 by pressing the ACbuttons.

If you want to ride without assistance as if

riding a normal bike, turn the system off via the

Mbutton.

During a ride with low engine speed

Land high assistance mode the motor

can start vibrating for a short time. In such

a case we recommend to immediately

decrease the level of assistance.

WALKING ASSISTANT

Walking assistant can be activated via pressing

and holding the Cbutton. To activate the

assistant, the assistance mode must be

between 1-5. This function serves to enable

better manipulation with e-bike, typically during

walking with the bike by your

side. The e-bikes speed will be between 4-6

km/h. Walking assistant will be turned off

immediately after letting go of the button.

WARNING: Do not block the e-bike

L after activation of the walking

assistant. The motor can get

damaged that way.

TURNING THE LIGHTING ON/OFF

To turn the lighting on/off, press and hold

the A button for 1 second. A symbol of “car’s

high beams” will appear on the display.

STATE OF CHARGE INDICATOR

It serves to get an image about the remaining

capacity of battery. If all LED diodes are on, the

battery is fully charged. In case of lower battery

voltage (lower current capacity) and higher

momentary load (i.e. riding uphill) the display

of capacity on the control panel can fluctuate.

More accurate data on the capacity of the

battery can be found on the indicator directly on

the batery.

PAS

MPH

Km/h

MOD

Mile Km

TRIP

ODO

TIME

MAX

AVG

ON/OFF assist. mode

lighting

state of charge

páteřová baterie nosičová baterie

(Tanka, Tanka Nexus, Tocho, Tocho Nexus, Dakotah)

LED  EBIKE CONTROL

BATTERY

ADVICE

IMPORTANT!

Battery is the most expensive part of the whole bike. Therefore, you should pay increased

attention to its recharging, storage and manipulation with it. Battery contains some chemicals

that can be dangerous if used improperly. Beware, lithium and its oxides are flammable in

contact with moisture.

Never take the battery apart. You could easily damage it with wrong procedure. Also, there is

a risk of injury because of combustion or even an explosion. Do bear in mind that by breaking

the warranty seal you lose the warranty on battery and all of its parts.

Before leaving the e-bike in a public place always lock the battery and take the key with you.

You will prevent the danger of your battery being stolen.

Always turn the battery o before any manipulation.

If the capacity of the battery is too low the motor will cease running smoothly and will

L start to run irregularly. In that case turn o the electric drive system and continue

without its help as if riding a normal bike. Heating of the battery is a regular occurrence, and it is

not a defect. The battery is protected by a temperature sensor and in case of its overheating

(i.e. because of high outer temperatures) it will disconnect automatically. Wait for it to cool down

to operational temperature and then continue in your ride.

Always have the battery locked during a

ride! The battery lock doesn’t only serve as a

protection from theft, but also secures its safe

attachment. Batteries without rocker switches

have a function of automatic shutdown after ca.

30 minutes (the period can differ according to

the type).

The battery is not able to detect a low

consumption of the display, so it can happen

that during a long ride with switched off help of

the motor the battery will automatically switch

off, and so will the whole system. By short-term

activation of the help you can prevent these

shutdowns.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Apache E-Bikes 2020 in the language / languages: English as an attachment in your email.

The manual is 1.01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Apache E-Bikes 2020 Manual

Product: