Manual Apa 16631 (page 9 of 24) (English, German, Dutch, French, Italian)

807551

Zoom out

Zoom in

1/24

6.2 PREPERATION 6.2 PREPERATION

6.3 CONNECTING THE BATTERY CHARGER

Caution: Make sure that the charger is

not connected to the power socket.

Always connect the red positive cable (+) of the charger

(Position 6 in the overview) to the positive terminal of

the battery rst. Then connect the black negative cable

(-) (Position 7 in the overview) to the negative terminal

of the battery. If you charge the battery in situ, connect

the black negative cable (-) to the car body (exposed

part), far away from the battery, the carburettor and fuel

lines. Always maintain this sequence. Now connect the

mains connection cable (Position 5 in the overview) to

a power socket.

Clean the battery terminals to remove dust and corrosion

residue.

Only for open batteries: Remove the plugs of the battery

cells. Check the liquid level in the cells, consult the ope-

rating instructions of your battery for more information.

Replenish only sucient distilled water to ensure that

the minimum lling level is achieved. The liquid will ex-

pand during the charging process and the battery may

overow. Leave the cells of the battery open until the end

of the charging process.

In case of closed and maintenance-free batteries, please

follow the instructions of the battery manufacturer to

the letter.

6.4 CHARGING THE BATTERY

6.4.1 SELECTING THE BATTERY TYPE

Press the selection switch for the battery type (Position 2

in the overview) several times to choose the correct

battery type. The dierent battery types are

toggled through in the following order: 6 V STD – 12 V

STD – 12 V AGM – 12 V Gel.

6.4.2 SELECTING THE DISPLAY

6.4.3 SELECTING THE CHARGING

MODE/JUMP START

Use the selection switch for the display (Position 3 in the

overview) to toggle the display from the current battery

voltage to the charge status in % (5% increments).

Use the selection switch for the charging mode (Posi-

tion 4 in the overview) to choose between the functions

SLOW (charge slowly), FAST (charge quickly) and START

(jump start).

Once the battery is fully charged the display shows FUL

(current battery voltage) or 100 in %.

6.5 REMOVING THE BATTERY CHARGER

6.6 JUMP START

Caution: First pull the plug out of the socket

and observe the sequence for disconnection.

This prevents sparks from forming. Since char-

ging generates a detonating gas, this is parti-

cularly important for the sake of your safety.

Before performing a jump start on your vehicle, read how

to carry out a jump start in your vehicle’s manual.

Switch o all electrical consumers in the vehicle (lights,

window heater, seat heating, etc.). Connect the device to

the vehicle battery as described in section 6.3. Use the

selection switch to choose the 12 V battery type appro-

priate for your vehicle. Position the selection switch for

charging mode/jump start to START.

Now start the vehicle’s engine. Do not operate the star-

ter for longer than 5 seconds. If the start attempt is not

successful, wait for at least three minutes before starting

the next attempt. After the third failed attempt, do not

attempt again. Instead, check your vehicle for faults.

Once the engine is running, remove the device as descri-

bed in section 6.5.

Disconnect the charger from the mains power supply.

Then disconnect the black clips (negative). Then remove the

battery clips from the positive terminal of the battery (red

clips).

Allow the battery to cool down. Only for open batteries:

Fill the cells with distilled water up to the level specied

by the battery manufacturer. Close the battery cells using

the caps.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Apa 16631 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2.43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Apa 16631 Manual

Product: