807549

Apa 16623 Manual

11
Zoom out
Zoom in
Previous page
1/32
Next page
11
4.1 Selection switch for charge current 2, 10, 20,
Auto (0-20) [A]
4.2 Selection switch for battery type Standard,
GEL, AGM
4.3 Selection switch for operating mode,
6 V charge, 12 V charge, jump-start 12 V,
constant-current source 13.6 V
Figure 4: Operating panel function selection
5.1 Control lamp for generator error
5.2 Control lamp for generator OK
5.3 Switch generator test ON
Figure 5: Operating panel for generator test
Only for open batteries: Remove the plugs of
the battery cells. Replenish distilled water up to the
minimum  ll level. Leave the cells of the battery open
until the end of the charging process.
With maintenance-free batteries, follow the instructions
of the battery manufacturer precisely.
6.2.2 CONNECTING THE BATTERY CHARGER
Make sure that the charger is not connected
to the power socket. Always  rst connect the
red plus cable (+) of the charger to the plus
pole of the battery. Subsequently, connect
the black minus cable (-) to the negative pole
of the battery. If you charge the battery in
situ, connect the black negative cable (-) to
the car body (exposed part), far away from
the battery, the carburettor and fuel lines.
Always maintain this sequence.
Now, connect the power plug of the charger to the mains
socket.
When the red control lamp „inverse“ (Position
3.5 in the overview) lights up, the charge
cables have been connected incorrectly.
Remove the pole callipers from the battery
terminals and connect them correctly.
6.2 CHARGING A BATTERY
6.2.1 PREPARATION
Clean the battery terminals to remove dust and corrosion
residue.
CAUTION
CAUTION
When the red control lamp „Error“ (Position
3.4 in the overview) lights up, check whether
the set charge program and the connected
battery correspond. Check the battery for
defects.
CAUTION
6.2.3 SETTING THE BATTERY CHARGER
First, in the function selection control panel (Position 4 in
the overview) use the selection switch for the operating
mode (Position 4.3 in the overview) to set the voltage for
the battery, 6V or 12V. Then, using the switch for battery
type (Position 4.2 in the overview), select the appropria-
te type for your battery. Using the selection switch for
the charge current (Position 4.1 in the overview), set the
appropriate charge current.
6.2.4 CHARGING PROCEDURE
Start the charging procedure by pressing the Start/Stop
button (Position 6 in the overview). In the control  eld for
the operating status (Position 3 in the overview), the
control lamp „Charge“ (Position 3.1 in the overview)
lights up. If the control lamp „Repair“ (Position 3.3 in the
overview) lights up, the charger carries out a program for
desulphation. With the selection button for the display
(Position 2.4 in the overview) you can set the display to
charge voltage, charge current and charge progress. The
control lamp „full“ (Position 3.2 in the overview) shows
that the battery is fully charged and that the battery
charger has switched over to maintenance mode.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Apa 16623 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Apa 16623 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info