Manual Apa 16553 - TMSPL-28 (page 10 of 28) (English, German, Dutch, French, Italian)

807545

Zoom out

Zoom in

1/28

6.3.1 CONNECTING THE POWER PACK

VEHICLES WITH NEGATIVE EARTH

Make sure that the Power Pack is switched o , the charge

status display must not light up. The Power Pack switches

itself o after around 10 seconds when not in use. Wait until

the Power Pack has switched o before continuing.

Switch o the ignition and all electrical consumers of the

vehicle (radio, lights, rear window heating, seat heating

etc.). Apply the parking brake.

First connect the red (+) pole callipers (Position 17 in the

overview) to the plus terminal of your vehicle battery.

The black (-) pole callipers (Position 15 in the overview) is

connected, as far as possible from the battery, to the motor

block or chassis (not to a painted part).

6.3.2 ATTEMPTING TO START

Switch on the Power Pack by pressing the ON/OFF switch.

Start the motor. Do not operate the starter for longer than

6 seconds. The battery of the Power Pack is not designed

for longer starting attempts. Pause for at least 5 minutes

between two starting attempts. If the motor does not start

after three attempts, abort the process and investigate the

cause of the defect.

6.3.3 REMOVING THE POWER PACK

First disconnect the black (-) pole calliper and attach the

pole calliper to the designated holder. Then disconnect

the red (+) pole calliper and attach the pole calliper to the

designated holder. Always maintain this sequence.

Recharge the Power Pack.

6.4 USE AS 12 V VOLTAGE SUPPLY

The Power Pack can be used as a 12 V direct current source

for many devices that can be operated with 12 V direct

current and a cigarette lighter plug. Plug the cigarette

lighter plug of the device you wish to operated into the

12 V outlets (Position 6 in the overview). The device you

wish to operate should not require a current greater than

10 A.

6.5 USE AS A USB CHARGER

Thanks to the USB port (Position 11 in the overview), the

Power Pack may also be used as a charger for mobi-

le telephones, smartphones, tablets, MP3 players and

similar devices. To recharge a USB device,  rst connect it with

the associated charging cable (not included in the scope of

delivery). Plug the USB plug on the charging cable into the

USB port on the Power Pack. Start charging by pressing the

ON/OFF switch (Position 8 in the overview).

6.6 LED INDICATOR FIELD

The Power Pack has an LED indicator  eld. This can be used

either as a work light or a warning light. Hold down the ON/

OFF switch (Position 8 in the overview) until the work light

switches on. Pressing the switch once again turns o the

warning light ( ashing), and pressing yet again turns the

LED indicator  eld o completely.

6.7 COMPRESSOR

In order to be able to work with the compressor,  rst remove

the air hose from the storage compartment (Position 16 in

the overview).

6.7.1 FILLING A TYRE USING THE CAR VALVE

SCHRADER VALVE

Open the lock on the valve

connection

Place the valve connection

on the valve

Lock the valve connection You can now  ll the tyres

using the compressor

Figure 3

Figure 4

Figure 2

Figure 5

To  ll, switch the compressor on using the ON/OFF switch

(Position 12 in the overview).

The manometer (Position 13 in the overview) is used to give a

rough approximation of the air pressure. When the desired air

pressure is reached, switch the compressor o . Remove the

valve connection in reverse order (Figures 5 – 2).

When  lling, always pay attention to

the correct air pressure (consult the

operating instructions of your vehicle for

information). The compressor is able to

supply of pressure of up to a maximum of

18 bar. If the pressure is too high, there is a

risk of explosion and injury.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Apa 16553 - TMSPL-28 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0.74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Apa 16553 - TMSPL-28 Manual

Product: