807545
9
Zoom out
Zoom in
Previous page
1/28
Next page
9
6.2.2 CHARGING THE POWER PACK WITH THE MOTOR
VEHICLE CHARGING CABLE
Make sure that the Power Pack is switched o . All control
lights and the work light must not be illuminated. Switch
o the compressor. Plug the coaxial connector of the motor
vehicle charging cable (Position 19 in the overview) into the
charging socket of the Power Pack (Position 9 in the over-
view). Now plug the motor vehicle charging cable into the
12 V on-board socket in your car. The charge status display
(Position 7 in the overview) is activated, and  ashes. If all
three lights on the charge status display are always lit, then
the Power Pack battery is fully charged. After charging,
rst disconnect the motor vehicle charging cable from the
on-board socket, then disconnect the coaxial connector from
the charging socket of the Power Pack.
6.2 CHARGING THE POWER PACK
Fully charge up the Power Pack after purchase with the plug
charger before initial use (Section 6.2.1)
CAUTION
Only charge the Power Pack when driving
or when the motor is running, otherwise
there is a risk that the starter battery of
your vehicle may be discharged.
Make sure that the Power Pack is switched o . All control lights
and the work light must not be illuminated. Switch o the
compressor. Plug the coaxial connector of the plug charger
(Position 18 in the overview) into the charging socket of
the Power Pack (Position 9 in the overview). Now, connect
the plug charger with the mains socket. The charge status
display (Position 7 in the overview) is activated, and  ashes.
If all three lights on the charge status display are always lit,
then the Power Pack battery is fully charged. After charging,
rst disconnect the plug charger from the mains socket, then
disconnect the coaxial connector from the charging socket of
the Power Pack.
6.2.1 CHARGING THE POWER PACK: WITH THE PLUG
CHARGER
6.3 STARTING AID
For instructions on carrying out a jump
start, read the manual of your vehicle or
ask your specialist workshop.
Disconnect all of the devices connected to the Power Pack
from the 12 V outlet socket (Position 6 in the overview) and
from the USB port (Position 11 in the overview).
Make sure that the Power Pack is fully charged. To do this,
press the ON/OFF switch (Position 8 in the overview). If all
three lights are illuminated on the charge status display
(Position 7 in the overview) then the Power Pack is ready to
use.
6. OPERATING INSTRUCTIONS
6.1 OVERVIEW
Figure 1: Overview
1 Handle
2 Control panel front
3 LED indicator  eld
4 Jump lead (+)
5 Jump lead (-)
6 12 V outlete
7 Charge status display
8 Switch
9 Charging socket
10 USB control light
11 USB port
12 Compressor switch
13 Manometer
14 Rear side of control panel
15 Pole calliper (-)
16 Air hose storage
compartment
17 Pole calliper (+)
18 Plug charger
19 Motor vehicle charging cable
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Apa 16553 - TMSPL-28 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Apa 16553 - TMSPL-28 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0.74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info