Manual Apa 16540 - SH317 (page 11 of 36) (English, German, Dutch, French, Italian)

807554

Zoom out

Zoom in

1/36

The starter aid function of the power

pack is only for vehicles with 12 V on-

board voltage. Before you start, read the

operating instructions of your vehicle, if

and how and external starter aid can be

used. Modern vehicles have sensitive

electronics and control devices that can

be damaged when handled incorrectly.

The control LED (position 5 in the overview) is now red.

For the initial charging process, leave the power pack

connected for 24 hours. For all subsequent charging

processes or directly after use charge no longer than

20 hours. Once the battery is fully charged, the LED is

green. After the charging process,  rst pull out the plug-

in charger from the socket and then unplug the coaxial

power connector from the charging socket of the power

pack. Now close the charging socket with the sealing

plug. If you press the battery test switch now, the control

LED is green.

6.2.2 CHARGING WITH THE 12V MOTOR VEHICLE

CHARGING CABLE

Turn the on-o switch (position 1 in the overview) to

the OFF position. Plug the coaxial power connector of

the cigarette lighter charging cable (position 12 in the

overview) into the charging socket of the power pack

(position 6 in the overview). Now plug the 12V vehicle

plug into the 12V socket of your vehicle. The control LED

(position 5 in the overview) is now red. Charge the power

pack for approx. 6 – 8 hours.

Make sure that the power pack is fully charged. To do so,

press the battery test switch (position 4 in the overview).

Once the control LED is green (position 5 in the overview),

the power pack is ready for use.

Once the battery is fully charged, the LED is green. After

the charging process,  rst pull out the 12V vehicle plug

from the socket of your vehicle and then unplug the

coaxial power connector from the charging socket of

the power pack. Now close the charging socket with the

sealing plug. If you press the battery test switch now, the

control LED is green.

Only charge the power pack while

driving or when the engine is running,

otherwise there is a risk of discharging

the starter battery of your vehicle.

6.3 STARTER AID

CAUTION

Start the engine. Do not let the starter motor work longer

than 6 s. The battery of the power pack is not suitable for

longer start attempts. Between start attempts, take a

break of at least 5 minutes. If the engine doesn‘t turn on

after several attempts, discontinue using the starter aid

and look for the cause of the malfunction.

Now turn the on-o switch to the OFF position. First

remove the black (-) terminal clamp, roll up the cable

and fasten the terminal clamp to its designated holder.

Then remove the red (+) terminal clamp, roll up the cable

and fasten the terminal clamp to its designated holder.

Always adhere to this sequence.

Recharge the power pack.

Turn o the ignition of your vehicle as well as all electrical

consumers (radio, light, rear window heating, seat

heaters, etc.). Enable the parking brake.

Turn the on-o switch (position 1 in the overview) to the

OFF position. First connect the red (+) terminal clamp

(position 11 in the overview) to the positive terminal of

your vehicle battery. Connect the black (-) terminal clamp

(position 10 in the overview) as far away from the battery

as possible to the engine block or chassis (no painted parts).

If the power pack is properly connected, the reverse polarity

protection view is lit green (position 2 in the overview). If

this is not the case, the reverse polarity protection view is lit

red and a warning signal is sounded. In this case, check the

connection of the terminal clamps and correct it. Now turn

the on-o switch to the ON position.

6.3.2 START ATTEMPT

6.3.3 REMOVING THE POWER PACK

6.3.1 CONNECTING THE POWER PACK

VEHICLES WITH NEGATIVE EARTH

In order to be able to work with the compressor,  rst take

the air hose (position 7 in the overview) out of the holder.

To do so, you brie y have to remove the red (+) terminal

clamp from its holder.

6.4 COMPRESSOR

Open the lock on

the valve connector

Place the valve

connector on the valve

6.4.1 FILLING A TYRE WITH THE CAR

VALVE / SCHRADER VALVE

Öffnen Sie die

Verriegelung

am Ventilanschluß

Setzen Sie den

Ventilanschluß auf

das Ventil

Verriegeln Sie den

Ventilanschluß

Sie können jetzt

den Reifen mit dem

Kompressor

befüllen

Fig. 2 Fig. 3

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Apa 16540 - SH317 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1.43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Apa 16540 - SH317 Manual

Product: