807560

Apa 16443 Power Pack Manual

10
Zoom out
Zoom in
Previous page
1/24
Next page
10
6. OPERATING INSTRUCTIONS
6.1 OVERVIEW
Press the switch once (Position 1 in the overview).
The display (Position 2 in the overview) is activated and
shows the charging level of the Powerpack as a
percentage (Position 13 in the overview).
6.2 CHECKING THE CHARGING LEVEL OF
THE POWERPACK
6.3 CHARGING THE POWERPACK
Use a USB charger with a 2 A output to charge the
Powerpack (not included in delivery!). Insert the USB-C
connector of the charging cable (Position 11 in the
overview) into the USB-C input (Position 3 in the
1 Switch
2 Display
3 USB-C input
4 USB output
5 LED light
6 EC5 starting help
connection
7 Control lamp Smartbox
Figure 1: Overview
8 Smartbox jump lead
9 Terminal clamp, black (-)
10 Terminal clamp, red (+)
11 USB-C charging cable
12 Bag
13 Charging level in %
14 Voltage
15 Current
16 Input / output
overview) of the Powerpack. Insert the USB-A
connector of the charging cable into the charger.
Connect the charging device to a socket.
The display shows the charging progress as a
percentage, 1% - 99%. At 100%, the battery of the
Powerpack is completely charged.
After charging, rst remove the charger from the socket
and then disconnect the charging cable from the charger
and the Powerpack.
6.4 JUMP START FOR 12 V VEHICLES
1. Switch o the ignition and all consumers on your
vehicle.
2. Ensure that the battery capacity of the Powerpack is
still at least 75% and that the battery callipers of your
vehicle battery are not soiled or oxidised.
3. Connect the Powerpack and the jump lead by
inserting the connector of the Smartbox (Position 8 in
the overview) of the jump lead into the starting help
connection (position 6 in the overview) of the Power-
pack. The LED light (Position 5 in the overview) is acti-
vated. Ensure that the connector is inserted rmly and
securely. The control lamp (Position 7 in the overview)
of the Smartbox ashes alternately red/green.
4. First connect the red terminal clamp (Position 10 in
the overview) of the jump lead with the positive pole,
and then the black terminal clamp (Position 9 in the
overview) with the negative pole of the vehicle bat-
tery. The terminal clamps must have a rm and secure
contact to the battery poles.
5. If the jump leads are connected correctly, the control
lamp shines green permanently, and a single tone is
issued.
Figure 2: Control lamp Smartbox
6. Start the vehicle motor. Do not operate the starter for
longer than 3 seconds. If the starting attempt was not
successful, wait at least two minutes before trying
again. After a third failed attempt, do not start a fur-
ther attempt and instead check your vehicle for faults.
7. Disconnect the jump lead from the Powerpack. Then
remove the terminal clamps from the vehicle battery.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Apa 16443 Power Pack at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Apa 16443 Power Pack in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2.76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info