801483
5
Zoom out
Zoom in
Previous page
1/21
Next page
ENGLISH
MiM Series | User manual
8
9
Series
User manual | MiM Series
3 | SYSTEM SETUP
For optimal transmission, the transmitter height must be at least 1 m (3ft) and put the
antenna vertically, upward. Avoid placing the transmitter close to metal objects or to
digital devices (CD players, computers, console, and so on).
The transmitter and receiver must be placed to have a straight “visual contact”.
3.1 | TRANSMITTER SETUP
The main screen of the display shows radio frequency, the selected operating mode
(MONO/STEREO), the transmission level of the AF1 and AF2 signals and the lock, if
it’s activated.
1 GROUP SELECTION
Press the SET button until when “GROUP” appears in the display.
Use the up and down buttons to select the desired group of frequency, then press
again SET to conrm the choice.
2 CHANNEL SELECTION
Press the SET button until when “CHANNEL” appears in the display.
Use the up and down buttons to select the desired channel, then press again SET
to conrm the choice. Simultaneously using more systems, it’s better to have them
on the same group but on different channels.
3 STEREO OR MONO OPERATING MODE (MiM 30T only)
Press the SET button until when “STEREO” or “MONO appears in the display. Use the
up and down buttons to select the desired mode, then press again SET to conrm
the choice. In Mono mode you will listen to AF2 signal, while in STEREO you listen
to both AF1 and AF2 signals.
ATTENTION: for MiM 20T the selection for MONO/STEREO mode is mechanically
achieved by a switch on transmitter rear panel.
4 LOCK ACTIVATION AND DEACTIVATION
Press the SET button until when the icon “LOCK” start flashing in the display, then
press the up and down buttons to conrm the choice.
To deactivate LOCK and edit the settings, you need to press the button
“SET” for 2 seconds.
ATTENTION: when LOCK icon is displayed, you can see the unit settings,
but these settings are not editable.
3.2 | BELTPACK RECEIVER SETUP
The main screen of the display shows radio frequency, the selected operating
mode (MONO/STEREO), the transmission level of the AF1 and AF2 signals,
batteries status, and the lock, if it’s activated. MiM 30R display shows also
information about TONE, LIMITER, and MIX features.
To do your settings, use the SET button and the up and down buttons. In MiM
30R there is also an ESC button, useful to immediately go back to main menu.
Press on the sides of the lid to lift the lid, and to access to the hidden buttons:
ESC and SET (MiM 30R) o up and down (MiM 20R).
1 AF1 AND AF2 CHANNELS VOLUME BALANCE (MiM 30R only)
Press the up/down buttons to adjust volume balance between AF1 and
AF2 of a Stereo signal If the transmitter is in Mono mode, using the up/
down buttons you set the position of the signal in the Stereo eld.
2 GROUP SELECTION
Press the SET button for 2 seconds until when “GROUP” starts flashing in
the display. Use the up and down buttons to select the desired frequency
group, then press again ESC (MiM 30R) or SET (MiM 20R) to exit the menu.
3 CHANNEL SELECTION
Press the SET button for 2 seconds to access the settings menu, then
press again SET until when “CHANNEL” starts flashing in the display.
Use the up and down buttons to select the desired frequency group, then
1
4
2
3
1
2
4 5 76
3
8
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ANT MIM 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ANT MIM 30 in the language / languages: English, German, Italian as an attachment in your email.

The manual is 4.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info