764159
7
Zoom out
Zoom in
Previous page
1/12
Next page
7
INSTALLATION
4. Separate the alarm from the mounting
plate. This may require you to turn the
alarm clockwise while holding the base
plate.
WARNING: do not screw the base plate
of the alarm to it’s mounting surface
with the alarm fitted to it. Dust from the
tting process could contaminate this
very sensitive device.
5. Locate the base plate in your chosen
position and mark the position of the
mounting holes. Drill the holes using
a 4.75 mm drill. Insert the anchor plugs
and screw the base plate to the chosen
position. DO NOT OVER-TIGHTEN THE
SCREWS. this will distort the base
plate.
Test button Sounder
Alarm base
mounting hole
Operating light
Alarm base
mounting hole
6. Fitting / Replacing the batteries:
a. Undo the screw and remove the
battery access door from the back of
the alarm.
When alarm is located on base unit,
twist in this direction to lock
Line up arrows
and insert
alarms into
base
Battery
cover
Fit two new AAA (LR03) batteries
(supplied with a new alarm) in the
battery bay making sure they are
fitted the correct way round by
referring to the diagram on the back
of the alarm. Allow ten seconds
before testing the alarm.
WARNING: USE ONLY DURACELL
MN2400 OR GP 24AU BATTERIES
OR ENERGIZER LROJ, OTHER
BATTERIES MAY BE INADEQUATE.
b. Refit the battery access door.
7. Line up the arrow on the back of the
alarm with the arrow inside the base
plate and inset the alarm. Once the
alarm is inside the base plate twist it
anti-clockwise to lock it into place.
8. Test the alarm.
ALARM TEST
1. Press and release the test button to
test alarm. The alarm should sound
three times.
2. After testing check that the red light
flashes approximately every 40
seconds.
3. Test the alarm once a week to ensure
correct operation.
Storage in low humidity, and certain
transportation conditions. may cause
electrostatic charges to build up in the
alarm system housing. Although harmless,
they may increase the length of time that
the horn sounds upon battery insertion or
test button operation. The condition may
be cleaned by gently wiping the outside of
the plastic cover with a clean, damp cloth.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AngelEye SA700-AE-UK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AngelEye SA700-AE-UK in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info