764158
8
Zoom out
Zoom in
Previous page
1/20
Next page
8
e Test the sounder, batteries and circuitry
by pressing and holding the Test button
for 1 second. The sounder should sound
as soon as the button is pressed, and
the Alarm LED will illuminate red for a
short time indicating that the sounder is
working and the batteries are providing
power to the unit. This test for the
sounder, batteries and circuitry should
be performed weekly.
WARNING: Prolonged exposure to the
sounder in close proximity to your ears
may damage your hearing.
Under normal operating conditions, the
batteries should last for at least 12 months.
The alarm will not protect against the risk
of carbon monoxide poisoning when the
batteries have drained.
WARNING: Prolonged exposure to
extreme high or low temperatures may
reduce the life of the batteries.
OPERATING FEATURES
Test / button feature
This button will:
Test the sounder, batteries and circuitry.
Allow you to test the sensor by
introducing a source of CO into the
alarm (see ‘Testing The Sensor’ below).
Silence the loud 85dB sounder during
an alarm (only possible when current
CO level is less than 50ppm).
Testing the sounder, batteries and
circuitry
Test the sounder, batteries and circuitry
by pressing and holding the Test button
for 1 second to confirm that the alarm is
operating properly. The sounder should
sound as soon as the button is pressed,
and the Alarm LED will illuminate red,
indicating that the sounder is working and
the batteries are providing power to the
unit. This test for the sounder, batteries
and circuitry should be performed weekly.
Testing the sensor
NOTE: Aerosol CO test kits or incense
sticks may be used to test the sensor.
Alternative sources of smoke, for example
an extinguished candle or match, will
not contain sufficient levels of carbon
monoxide to obtain a response from the
alarm during this test. Please note your
CO alarm will not detect smoke.
If testing the sensor for the first time after
installation, or replacing the batteries,
make sure that the alarm has completed
the initial 3 minute warm up period and
the power LED is flashing green once
every minute.
CAUTION: Sensor testing should only be
performed by a responsible adult.
Read all steps thoroughly before
attempting to test your the sensor
Step 1 If the alarm is wall or ceiling
mounted unhook the alarm
from the screws.
Step 2 Cover the sounder vents with
one hand. Press and hold the
Test button down with your
thumb/finger until the Power
LED illuminates green and the
sounder sounds for a second
time (this should happen after
around 5 seconds).
Test Button
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AngelEye CO-FA-AE-9B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AngelEye CO-FA-AE-9B in the language / languages: English as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info