537060
13
Zoom out
Zoom in
Previous page
1/16
Next page
Warnings
FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
THIS PRODUCT IS NOT A MEDICAL DEVICE DESIGNED TO PREVENT
CASES OF SUDDEN INFANT DEATH SYNDROME (SIDS OR COT DEATH).
THIS PRODUCT IS NOT A SUBSTITUTE FOR DIRECT SUPERVISION OF
YOUR BABY. CHECK YOUR BABY’S ACTIVITIES AT REGULAR INTERVALS.
MONITORING OF PREMATURE BABIES, OR BABIES CONSIDERED TO BE
AT RISK, SHOULD BE CARRIED OUT ONLY UNDER THE SUPERVISION OF A
DOCTOR OR HEALTH PROFESSIONAL.
ALWAYS CHECK YOUR BABY IMMEDIATELY WHEN THE ALARM SOUNDS.
WARNING: THIS PRODUCT IS NOT A TOY.
Please read Step 1 (Installation of SensorPad), Step 4 (Testing your Baby
Monitor) and the Troubleshooting section to ensure your Angelcare Baby
Monitor is installed correctly.
DO NOT put the Parent Unit near wireless devices or a microwave oven.
Such devices can disrupt the transmission of the alarm signal.
The Angelcare Baby Monitor is perfectly safe. The SensorPad and its cord are
entirely passive. They carry no electrical current and do not radiate any form
of energy. The Nursery Unit emits only very low power radio signals through
its antenna.
These signals do not present a safety hazard.
The SensorPad may detect movement from many sources from both inside
and outside your baby’s room, e.g. washing machine, loud music, etc. Make
sure that all vibration sources are eliminated before using the Angelcare
Baby Monitor. When the monitor is in use, DO NOT use a crib mobile or other
crib accessories that produce vibrations. This can prevent the movement
alarm from working properly as the monitor will still be detecting movement.
Please do not touch the baby’s bed when the monitor is in use.
Your Angelcare Baby Monitor can be used in any crib that is stationary and
designed to safely hold a baby. If your crib has a spring or slatted base you
will need to place a piece of plywood under the SensorPad. Please see Step
1 for correct installation of the SensorPad. Only use your Angelcare Baby
Monitor in a stationary sleeping environment such as a cot (bed) or moses
basket where the SensorPad can rest on a completely fl at, rm surface.
You may experience false alarms for several reasons. The most common
reason is the Nursery Unit has not been turned off after you have removed
your baby from the crib. Another reason is if the SensorPad has not been
placed under the mattress properly. Be sure the SensorPad is placed on a
at, fi rm surface with the printed side facing up. The sensitivity level may
also need to be adjusted. Please see Step 1 for the correct installation of the
SensorPad.
If the monitor has been stored or has been exposed to hot or cold
temperatures, it may take up to one hour before the temperature displayed
on the Parent Unit is accurate.
ALWAYS place the Parent and Nursery Units on a fl at surface in an upright
position, away from baby’s reach.
Allow for proper ventilation when units are in use. Do not cover the Nursery
Unit or Parent Units with any object such as a blanket. Do not place it in a
drawer or in any location which would muffl e the sound or interfere with the
normal fl ow of air.
Plug the AC adaptor into a convenient accessible mains socket outlet.
Keep all wires out of baby’s reach as this could cause a possible
entanglement or strangulation injury.
DO NOT touch the end of the AC adaptor cord when it is plugged into the
mains.
The Angelcare Baby Monitor uses public airwaves to transmit signals. The
Parent Unit may pick up signals or interference from other baby monitors
in your area. Your monitor may also be picked up by receivers in other
households. To protect your privacy, make sure both units are in the OFF
position when not in use and change the channels regularly.
Do not use the Nursery Unit if:
• The AC adaptor wire or plugs have been damaged
• The unit has been exposed to liquids
• The unit has been dropped or is damaged
DO NOT DISASSEMBLE the Nursery Unit, Parent Unit, Parent Unit base,
SensorPad or AC Adaptors. There are no user-serviceable parts inside. Risk
of electrical shock, fi re or death.
The antenna used for this transmitter must be installed least 20cm (7.9”)
away from all human beings and must not be collocated or operating in
conjunction with any other antenna or transmitter.
IMPORTANT: You must use only rechargeable batteries in the Parent Unit. DO
NOT use alkaline batteries or you will severely damage the unit. Charge the
batteries for 16 hours prior to fi rst use. Be sure to have the monitor in the
OFF position during this period. Only use the AC adaptors included with your
monitor.
DO NOT use these adapters with any other equipment. When unplugging the
AC adapter from the Nursery Unit, be sure it is switched to the OFF position.
If this is not the case, the unit will revert to battery mode if batteries are
installed.
You can use rechargeable batteries in the Nursery Unit, however, they will
not be recharged by plugging in the AC adaptor.
To recharge, remove the batteries and use an external charger.
ONLY use AAA (LR03) rechargeable batteries and/or the AC adaptor provided
for the Parent Unit.
FCC WARNINGS
Modifi cations not authorised by the manufacturer may void users’ authority
to operate this device.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation
ErP COMPLIANCE - UK
ONLY USE ORIGINAL ANGELCARE AC ADAPTORS, MODEL NO.
T07505B001.
Consumer Helpline: 0845 009 1789 | www.angelcare-uk.co.uk
13
AC1100_Manual.indd 13AC1100_Manual.indd 13 19/5/11 2:39:20 pm19/5/11 2:39:20 pm
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Angelcare AC1100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Angelcare AC1100 in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Angelcare AC1100

Angelcare AC1100 User Manual - Dutch, Danish - 83 pages

Angelcare AC1100 User Manual - French - 59 pages

Angelcare AC1100 User Manual - Polish, Portuguese, Swedish - 83 pages

Angelcare AC1100 User Manual - Spanish - 59 pages

Angelcare AC1100 User Manual - Finnish - 83 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info