541773
6
Zoom out
Zoom in
Previous page
1/9
Next page
5
The Rear Panel
SVT-8 PRO Bass Amplifier
20. AC LINE IN: Firmly insert the supplied AC
power cord into this socket until it is fully seat-
ed. Plug the male end of the cord into a
grounded AC outlet. DO NOT DEFEAT THE
GROUND PRONG OF THE AC PLUG!
21. BAL. OUT: This jack supplies a line level
signal for connection to a house mixing board,
recording console or external amplifier. The sig-
nal level at this jack is governed by the Post/Pre
switch (#23).
22. GND/LIFT: Use this switch to lift the ground
connection at the Bal. Out jack to help eliminate
hum in the Bal. Out signal.
23. POST/PRE: The signal at the Bal. Out jack
(#21) can be set to either Pre or Post-EQ with
this switch. With the swi
tch in the OUT position,
the signal at the jacks is Pre-EQ. This is a direct
output not affected by any EQ or boost settings.
With the switch depressed, the signal is Post-
EQ and is controlled and modified by the tone
controls and the effects loop.
24: TUNER OUT: This jack is provided for con-
nection to an electronic tuner and is always
“live, even when the Mute switch (#3) is
engaged. This allows for “silent tuning as well
as a monitor feed which stays hot even when
the house mix is muted.
25. SPEAKERS: These output jacks supply
speaker-level power to the speaker cabinet.
The rated power output is 1300 watts rms
into 4 ohms or 2500 watts rms into 2 ohms
(minimum load).
WARNING: Use speaker cables to make
the connections. Do not use instrument
cables as they may overheat.
Pin 1+ = hot
Pin 1– = return
26. CIRCUIT BREAKER: The SVT-8 PRO
employs an AC line circuit breaker to
help pro-
tect against damages due to excessive current
demands. If the amplifier stops working, check
the circuit breaker.
27: POWER AMP IN: This jack connects an
external preamp directly to the power amp.
When using an external source, connect the
output of the source to this jack by means of a
shielded signal cable to feed the signal into the
power amp section. The internal signal is dis-
connected when a connector is inserted into
this jack.
28. PREAMP OUT: Use this jack to send a sig-
nal from the internal preamp to an auxiliary
power amplifier, mixing console, monitor sys-
tem, or
house PA system. The signal at this
jack is post-EQ.
29. EFFECTS LOOP RETURN: When using
an external signal processor, connect the out-
put of the device to this jack by means of a
shielded signal cable.
30. EFFECTS LOOP SEND: When using an
external signal processor, connect this jack to
the input of the device by means of a shielded
signal cable.
31. FOOTSWITCH: Connect a two-button
(ring/tip/sleeve) footswitch to this jack to control
the Power Reduction and the Mute functions.
(Mute = tip/sleeve; Power Reduction = ring/
sleeve.)
NOTE: A footswitch may be purchased at
your local Ampeg Dealer or ordered directly from
LOUD Technologies Inc. Be sure to ask for
model #AFP2.
IMPORTANT: This unit employs forced air
cooling by means of an internal fan. The
rear and side ventillation slots must remain
unobstructed when operating this amplifier.
When mounting the unit in a rack make sure
there is ample room for proper air circulation.
The rack must be constructed and positioned
in such a manner to allow proper air flow and
the exhausting of hot air away from the rack
at all times.
WA R NING :
Made In T he U.S .A .
L OUD T E CH NOL OG IE S, INC .
10240V 50/60Hz 300VA
250 0W @ 2 O HMS
130 0W @ 4 O HMS
C LA SS 2 W IR ING
T his device c ompli es with pa rt 15 of th e F CC R ule s.
Op erati on is su bjec t to the follow ing two c ond ition s:
this devic e m ay not c au se ha rmfu l in terferenc e, and this
dev ice mu st acc ept any in terfe renc e r ec eive d, i nclu ding
inte rfer enc e th at m ay ca us e u ndes ir ed o pera tion .
26 27 28 3129 30
20 2421 2522 23
26 27 28 3129 30
20 2421 2522 23
W
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ampeg SVT-8 Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ampeg SVT-8 Pro in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info