541773
5
Zoom out
Zoom in
Previous page
1/9
Next page
3
An Introduction to your new Ampeg SVT-8 PRO Bass Amplifier
The harmonically rich sound and legendary performance of the AMPEG SVT are redefined in the SVT-8 PRO.
This versatile and powerful bass amplifier delivers up to 2500 watts of unsurpassed musical power, and offers
the classic vibrancy of tubes with several outstanding features.
All of the features and controls of your SVT-8 PRO are covered in detail within the pages of this user’s
guide. We recommend that you go over them before you use the amplifier.
Features
In the world of high performance bass amps, Ampeg’s SVT amplifiers stand alone. In true Ampeg tradi-
tion, the SVT-8 PRO offers you more power, performance and flexibility than any other bass amplifier in its
class. Below are some of the outstanding features of your new amplifier - features which set it apart from
the competition!
-12DB SWITCH: A switchable input pad which optimizes the input signal level for
use with basses with active electronics or very “hot” pickups
MUTE SWITCH, TUNER OUT JACK: Allows you to tune your bass without hearing
it through the amplifier
5-POSITION ULTRA LOW SWITCH: Five different settings for the Ultra Low pro-
vide the ultimate in bottom end response
ULTRA HIGH AND BRIGHT SWITCHES: Allows you to tailor your high frequency
response in many different ways at the touch of a button
5-POSITION MIDRANGE SELECTOR: Choose from the five center frequency
points available to get just the right midrange voice
POWER REDUCTION CIRCUIT: A simulated tube power amp section allows you to
get the desired amount of “tube power amp growl” at any volume
TRANSFORMER BALANCED LINE OUTPUT: Allows you to send a high quality
line level signal to the house mixing board, a recording console, or another amplifi-
er - switchable for pre or post EQ with a switchable ground lift
EFFECTS LOOP: Allows for virtually noise-free connection for use with you favorite
effects
FOOTSWITCH CONTROL: Allows hands-free remote control over the Mute and
Power Reduction features
CIRCUIT BREAKER PROTECTION: A heavy duty resettable circuit breaker pro-
vides protection against fault conditions
SPEAKON
®
SPEAKER OUTPUT JACKS: For the ultimate connection and trans-
mission of power to your speakers
ULTIMATE POWER: 1300 watts into 4 ohms, 2500 watts into 2 ohms
Speakon
®
is a registered trademark of Neutrik AG.
SVT-8 PRO Bass Amplifier
4
The Front Panel
SVT-8 PRO Bass Amplifier
INPUT
12dB
MUTE
0 10
12345
PEAK
ULTRA HIGH
BRIGHT
GAIN
0 10 0 10
MIDRANGE
0 10
ON
TREBLE DRIVE POWER
POWER
MASTER
FAU LT
LIMIT
ON
POWER REDUCTION
PULL ON
BASSULTRA LOW
12345
FREQUENCY
1 3 4 9 10 12 16 17 18 1913 14 155 6 112 87
1. INPUT: Connect your bass guitar here by
means of a shielded signal cable.
2. -12dB: This switch, when depressed, attenu-
ates the input signal by 12dB. Attenuation allows
the Gain control (#4) to be used over a larger por-
tion of its range. If clipping is indicated with the
Gain way down, attenuation is needed.
3. MUTE: This switch, when depressed, mutes all
outputs except the Tuner Out (#24, rear panel).
This allows you to use an electronic tuner without
having to adjust any levels or turn down your
house sound. A footswitch may be used to control
the mute function as long as this switch is in the
out position.
4. GAIN: This controls the gain of the preamp.
Adjust this control until the Peak LED (#5) flickers
on strong signal peaks (but is not illuminated con-
stantly while playing).
5. PEAK: This LED illuminates when the signal
level into the preamp or power amp nears clip-
ping. Adjust the Gain control (#4) until a strong
signal from your instrument causes this LED to
flicker with the Master control (#16) set low.
NOTE: If the LED flickers frequently with the Gain
at a low setting, use the -12dB switch (#2) to
attenuate the input signal and readjust the Gain.
6. ULTRA LOW: Use this five-position rotary
switch to optimize the low end response as fol-
lows:
1: Off – flat low frequency response
2: Sub Cut – reduces frequencies below the
bass range to protect your speakers
3: Low Cut Classic – provides a low cut equal
to our original SVT Classic amplifier
4: Ultra Low Classic – contours the sound to
emphasize the low end just like our original
SVT amplifier
5: Ultra Low Modern – provides a substantial
low end boost
7. ULTRA HIGH: This switch, when depressed,
adds about a 16dB boost to the high frequencies
around 8kHz, depending on the setting of the
Gain control.
8. BRIGHT: This switch, when depressed, adds a
6dB boost to the high frequencies at 3kHz.
9. BASS: Use this control to adjust the low fre-
quency output level. This control provides +17/-13
dB at 20Hz.
10. MIDRANGE: Use this control to adjust the
midrange frequency output. This control provides
+/-20dB at the frequency selected by the adjacent
Frequency control (#11).
11. FREQUENCY: Use this control to select the
center frequency for the Midrange control (#10)
as follows:
1: 220Hz
2: 450Hz
3: 800Hz
4: 1.6kHz
5: 3kHz
12. TREBLE: Use this control to adjust the high
frequency output level. This control provides +18/
-20dB at 7kHz.
13. POWER REDUCTION ON: This LED illumi-
nates when the Power Reduction function is
active.
14. POWER REDUCTION DRIVE / PULL ON:
This control, when engaged, determines the sig-
nal level sent to the simulated tube power amp
section. This control works in conjuntion with the
other preamp controls in determining how hard
the “power amp” is driven. The Power Reduction
is engaged when this control is pulled out slightly
until it clicks.
15. POWER REDUCTION POWER: This control
sets the output level of the simulated tube power
amp section. This allows you to obtain the desired
amount of “tube power amp growl” at any volume.
16. MASTER: Use this control to adjust the over-
all level of the amplifier.
17. LIMIT: The SVT-8 PRO employs an internal
limiter to help prevent overdriving the power amp.
This LED illuminates when the Limiter is activat-
ed, indicating that the levels are near clipping.
Reduce the Master control (#16) if this LED illu-
minates continuously while playing.
18. FAULT: This LED illuminates when faulty con-
ditions cause the amplifier to protect itself against
damages. If this LED should illuminate while play-
ing, turn the amplifier off, wait ten seconds, then
turn the amplifier back on. If the Fault LED con-
tinues to illuminate refer the amplifier to a qualified
Ampeg service center.
19. POWER: Use this switch to turn the amplifier
on (top of the switch depressed) and off (bottom
of the switch depressed). The adjacent LED illu-
minates when the amplifier is turned on.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ampeg SVT-8 Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ampeg SVT-8 Pro in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info