733756
28
Zoom out
Zoom in
Previous page
1/42
Next page
26
User’s manual
EN
SECONDARY AREAS – PROGRAMMING MODE
If the area to be mowed includes secondary areas based on the denition given in the chapter “Preparation and Marking the
Boundaries of the Work Areas”, then it is necessary to program the secondary areas so the robot knows how to reach them and
how many times.
SECONDARY AREA: function for dening the automatic mowing of a secondary area.
-
Percentage: allows setting the dimensions of the secondary
area to be mowed in respect to entire lawn surface. Below is a
table to use as a guide for conguring a secondary area:
10% indicates a very small area.
30% indicates an area which is approximately one third of
the entire garden.
50% indicates an area which is approximately half of the
entire garden.
80% indicates a secondary area which is bigger than the
primary area.
100% the robot will follow the perimeter wire to mow the
secondary area each time it exits the charging station.
primary area
clockwise directionanti-clockwise direction
secondary area 1
(30%, 60MT, clokwise)
secondary area 2
(20%, 30MT, Anti-clokwise)
-
Distance: this allows setting the distance necessary for the robot to reach the internal part of the secondary area following
the perimeter wire. It is recommended to measure half the distance of the secondary area to ensure that the robot starts
working inside that area.
-
Direction: indicates the shortest direction for reaching the secondary area. The direction can be clockwise or counter-
clockwise. The robot exits from the charging station and follows the wire in the indicated direction to reach the secondary
area.
-
Mode: indicates the method for reaching the secondary area. Use the “Follow wire” method when there are lots of obstacles
in the garden close to the perimeter wire (less than 2 m) or when there are tight areas to pass through (less than 2 m) to reach
the secondary areas. In all other cases use the “V-Meter” method.
“Follow wire”. The robot reaches the secondary area positioning its wheels astride the perimeter wire.
“V-Meter”. The robot reaches the secondary area running along the perimeter wire at an indicative distance from a few
cm to 1 m (3.2 ')..
SECONDARY AREA 2: function for dening the automatic mowing of secondary area number 2. This setting uses the same
conguration parameters as those used for secondary area 1.
SECONDARY AREA 3: (only for some versions, see “Technical Specications”). Function for dening the automatic mowing of
secondary area number 3. This setting uses the same conguration parameters as those used for secondary area 1.
SAFETY – PROGRAMMING MODE
CHANGE PASSWORD: function for setting or changing the password.
-
No: the password entered does not need to be changed.
-
Yes: for entering or changing the password which will be used to start the robot. You will prompted to enter the following
information:
password: enter the old password (manufacturer’s default 0000).
new password: enter the new password. The password must be different from 0000.
repeat password: enter the new password again.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ambrogio L85 Evolution at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ambrogio L85 Evolution in the language / languages: English as an attachment in your email.

The manual is 5,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ambrogio L85 Evolution

Ambrogio L85 Evolution User Manual - Dutch - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info