Manual Alpine RUX-C800 (page 35 of 67) (English)

471407

Zoom out

Zoom in

1/67

33-EN

01GB06PXAH800.fm

ALPINE PXA-H800_EN 68-13530Z65-A (B5)

From a PC

When setting is complete, click [Close Window].

• After the setting, it is recommended to store the setting contents on

the unit. For details, refer to “Storing the Preset Values (Preset

Store)” (page 12).

The test tones guide you through the volume adjustments of the

different speakers. When levels are balanced, a strong sense of presence

can be heard from the different speakers at the listening position. (Initial

setting: “±0dB”)

Click [Start] for “Test Tone Output.”

Output Level screen will be displayed and the test tone is

produced from the left front speaker.

Select a channel and click.

Setting channel: Left/Center/Right/Right Surround/Left

Surround

• Channels to be set vary depending on the system set in “Setting the

Speaker System (Output System Select)” (page 13).

Adjust the speaker volumes for each channel to

make them equal while the test tone is output from

each channel. Drag [ ] or click [ ] or [ ] to make

adjustments.

Level: -10 to +10 dB (in 1 dB steps)

Adjust based on the front speakers.

Repeat Steps 2 and 3 to set the level for each

channel.

To stop the test tone, click [Stop].

• Avoid stopping, pausing, switching the disc, cueing, fast-

forwarding or switching the audio channel of this unit while

making this adjustment. The setting is cancelled if the decode

mode is switched.

To install a center speaker, it must be located in the dash, an equal

distance between the Left and Right speakers. In most cases, this is very

difficult to achieve. Using Bi-PHANTOM, a virtual center speaker is

created by sending the center channel information to both the Left and

Right speakers. Adjusting the center width in Dolby Pro Logic II

“Music” (see “Using Dolby Pro Logic II (Dolby Pro Logic II)” on

page 31), makes this function ineffective. (Initial setting: “OFF”,

“±0dB”)

Click [ON] for “BI-PHANTOM.”

Turning this feature on creates the acoustic image in which

the center speaker is virtually located exactly in front of the

listener by sending the sound of the center speaker to both

sides.

Click [ ] for “Level” and select and click the level

you want from the pull-down menu.

Level: -5 to +5 dB (in 1 dB step)

The level can be adjusted between -5 and +5. When the

level becomes greater, the acoustic image moves from the

center speaker location towards both sides.

• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding

or switching the audio channel of this unit while making this

adjustment. The setting is cancelled if the decode mode is switched.

• When the Center speaker is off in “Setting the Speaker System

(Output System Select)” (page 13)/ “Setting the Speakers (Speaker

Setup)/Setting the Subwoofers” (page 14), this item cannot be set.

• Effective only for Dolby Pro Logic II, EUPHONY and DTS (with

Center signal).

This function mixes the front channel audio signals with the audio

signals output from the rear speakers, improving the sound in the

vehicle’s rear seat. This is used in a system where there is no subwoofer

and the rear speakers can produce lower frequency sounds than the front

speakers. (Initial setting: “OFF”, “±0dB”)

Click [ON] for “ Rear Mix.”

Turning this feature on mixes the audio signals output from

the rear speakers with the front audio signals.

Click [ ] for “Level” and select and click the level

you want from the pull-down menu.

Level: -6/-3/0/+3/+6 dB

The level can be adjusted in 5 steps. The higher the level,

the more the low range audio is output from the rear

speakers. (Depending on the software such as DVD, the

effect may vary.)

Adjusting the Speaker Volume Level

(Output Level)

Adjusting the Acoustic Image (BI-

PHANTOM)

Mixing the Low Range Audio for the Rear

(Rear Mix)

01GB00PXAH800.book Page 33 Tuesday, February 8, 2011 9:04 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Alpine RUX-C800 in the language / languages: English as an attachment in your email.

The manual is 11,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Alpine RUX-C800 Manual

Product: