66348
5
Zoom out
Zoom in
Previous page
1/60
Next page
3-EN
ALPINE KTX-100EQ 68-08564Z99-A (EN)
Before Setting MultEQ
Read following provisions before setting MultEQ.
The MultEQ setting should be made in as quiet a place as possible after turning off the engine, air-
conditioner and heater. If you have a car phone or cellular phone in the vehicle, remove them from the
vehicle or turn its power off. If sound other than measurement tone to be measured (engine or receiving
sound of car phone, etc.) occur, sound measurement in the vehicle may not be accurate.
When setting MultEQ, be sure to use the microphone supplied with this unit. If a microphone other than
the supplied one is used, measurement may not be possible or sound measurement in the vehicle may not
be accurate.
If a power amplifier or a powered subwoofer with an input level control is connected and this level is
lowered, measurement may not be possible. However, the input level should set lowered than normal
level to adequately perform measurement.
If a power amplifier with a low-pass filter is connected, measure MultEQ when the low-pass filter of the
power amplifier is turned off. If a low-pass filter is built into the powered subwoofer or power amplifier
for subwoofer, set the cut-off frequency to the highest value.
If MultEQ is set and the function is turned on, MX, X-OVER, Time Correction, User’s EQ, Parametric
EQ and Graphic EQ are automatically adjusted. Therefore, they cannot be individually adjusted.
After you have stored the result of MultEQ you adjusted in the CDA-9887/CDA-9887R, if you store the
results of MultEQ again in the CDA-9887/CDA-9887R, the previously stored MultEQ will be
completely cleared and replaced by the new one.
Setting MultEQ
1
Prepare for MultEQ setting.
Park the vehicle in a quiet location.
Close doors, windows, sunroof, etc.
Turn off the engine of the vehicle.
Set the air-conditioner and heater to OFF.
2
Set the key position of the vehicle to ACC or turn it on.
If an air-conditioner or heater is turned on, turn it off. Measurement should not be performed if air-conditioner
or heater noise is present.
WARNING
While driving, do not set up MultEQ.
To prevent accidents, do not set up MultEQ while driving. The setting of the MultEQ
function is required to mount the microphone in the vehicle in order to measure sound
characteristics. Also, during measurement, loud measurement tone (signal) from the
speakers may be output. Making such settings may distract you from driving and result in
an accident.
KTX-100EQ.book Page 3 Friday, April 13, 2007 4:31 PM
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Alpine KTX-100EQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Alpine KTX-100EQ in the language / languages: English as an attachment in your email.

The manual is 3,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info